Multiplus 12/3000/120/16

0 out of 5


Multifunctional, with intelligent power management
The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge
technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the
MultiPlus has several advanced features, as outlined below.
Two AC Outputs
The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of
a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
computers and other electronic equipment will continue to operate without disruption.
The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the
battery, like a water heater for example, can be connected to this output (second output available on models rated at
3kVA and more).
Virtually unlimited power thanks to parallel operation
Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide
15kW / 18kVA output power with 420 Amps of charging capacity.
Three phase capability
In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three
strings of six parallel units a 45 kW / 54 kVA three phase inverter and 1260 A charger can be built.
Split phase options
Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per
phase, to supply up to 30 kW / 36 kVA of split phase power.
Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on to a ‘European’ inverter programmed to supply 240 V / 60 Hz.
PowerControl – Dealing with limited generator, shore side or grid power
The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side
supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore
current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus
preventing the generator or shore supply from being overloaded.
PowerAssist – Boosting the capacity of shore or generator power
This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the
capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will
make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When
the load reduces, the spare power is used to recharge the battery.
Four stage adaptive charger and dual bank battery charging
The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software.
The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage
for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger
datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second
battery using an independent trickle charge output intended for a main engine or generator starter battery.
System configuring has never been easier
After installation, the MultiPlus is ready to go.
If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even
parallel and 3-phase operation can be programmed with DIP switches: no computer needed!
Alternatively, VE.Net can be used instead of the DIP switches.
And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several
new, advanced, features



PowerControl Yes
PowerAssist Yes
Transfer switch (A) 50
Parallel and 3-phase operation Yes
Input voltage range (V DC) 9,5 – 17 V 19 – 33 V
Output Output voltage: 120 VAC ± 2% Frequency: 60 Hz ± 0,1% (1)
Cont. output power at 25ºC / 77°F (VA) (3) 3000
Cont. output power at 25ºC / 77°F (W)  2400
Cont. output power at 40ºC / 104°F (W)  2200
Cont. output power at 65ºC / 150°F (W)  1700
Peak power (W)  6000
Maximum efficiency (%)  93 / 94
Zero load power (W)  20 / 20
Zero load power in AES mode (W)  15 / 15
Zero load power in Search mode (W)  8 / 10
AC Input Input voltage range: 95-140 VAC Input frequency: 45 – 65 Hz Power factor: 1
Charge voltage ‘absorption’ (V DC) 14,4 / 28,8
Charge voltage ‘float’ (V DC) 13,8 / 27,6
Storage mode (V DC) 13,2 / 26,4
Charge current house battery (A) (4)  120 / 70
Charge current starter battery (A) 4
Battery temperature sensor yes
Auxiliary output (5) n. a. Yes (32A)
Programmable relay (6) Yes (1x) Yes (3x)
Protection (2) a – g
VE.Bus communication port For parallel and three phase operation, remote monitoring and system integration
General purpose com. port (7)Yes (2x)
Remote on-off Yes
Common Characteristics Operating temp. range: -40 – +65°C / -40 to 150°F (fan assisted cooling) Humidity (non-condensing): max 95%
Common Characteristics Material & Colour: aluminium (blue RAL 5012) Protection category: IP 21
Battery-connection  M8 bolts (2 plus and 2 minus connections)
120 V AC-connection Screw-terminal 6 AWG (13mm²)
Weight . 19kg 40 lbs.
Dimensions (hxwxd in mm and inches)  362x258x218 mm 14.3×10.2×8.6 inch
Safety EN 60335-1, EN 60335-2-29
Emission Immunity EN 55014-1, EN 55014-2, EN 61000-3-3
1) Can be adjusted to 60 HZ; 120 V 60 Hz on request
2) Protection key:
a) output short circuit
b) overload
c) battery voltage too high
d) battery voltage too low
e) temperature too high
f) 230 VAC on inverter output
g) input voltage ripple too high
3) Non-linear load, crest factor 3:1
4) At 75˚F ambient
5) Switches off when no external AC source available
6) Programmable relay that can a.o. be set for general
DC under voltage or genset start/stop function
AC rating: 230 V/4 A
DC rating: 4 A up to 35 VDC, 1 A up to 60 VDC
7) A.o. to communicate with a Lithium Ion battery BMS

Additional information

Weight 19 kg
Dimensions 36.2 × 25.8 × 21.8 cm


There are no reviews yet.

Be the first to review “Multiplus 12/3000/120/16”