Interesting Facts
A dual battery system is not required as the 12v function is only used while
travelling.
Gas or 220V is used when stationary so there is no need for forced drives to charge batteries.

Your freezer
: has 75mm foam insulation which increases your cold hold over time when not switched
on compared to other freezers.
: has no moving parts inside the absorption system which makes repair and maintenance
inexpensive.
: is level sensitive hence proper levelling must be done when stationary.
: is proudly manufactured in South Africa.
: is capable of freezing to 44°C below ambient.
Example: -12°C @ 32°C
-20°C @ 20°C
: is capable of freezing 2 kg of water in 24 hours while keeping everything else frozen.
: is equipped with a gas safety valve which will cut the gas flow to the
burner in less than 60 seconds in the event of the burner flame going out.
: will only use between 400 – 500g of gas per 24 hours. A 9 kg gas bottle will last you
approximately 18 – 21 days.
: gas function is ideal for those unforeseen black outs at home.
Your Cooler Box
: has 75mm foam for maximum insulation.
: has a aluminium bin to transfer the cold all around.
: is perfect to keep you meat frozen for those long weekends.

Input voltage range and frequency 180-265 VAC 45-65 Hz

Efficiency 96%

No load power consumption 0.5W

Charge voltage ‘absorption’ Normal: 28,8V

High: 29,4V

Li-ion: 28,4V

Charge voltage ‘float’ Normal: 27,6V

High: 27,6V

Li-ion: 27,0V

Charge voltage ‘storage’ Normal: 26,4V

High: 26,4V

Li-ion: 27,0V

Charge current, normal mode 12A

Charge current, LOW 4A

Charge algorithm 5-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +60°C (full rated output up to 40°C) Derate 3% per °C above 40°C

Humidity Up to 100%

Start interrupt option (Si) Short circuit proof, current limit 0,5 A

(12/25 and 24/12 models only) Output voltage: max one volt lower than main output

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery-connection Black and red cable of 1,5 meter

230 V AC-connection Cable of 1,5 meter with CEE 7/7 plug

Protection category IP67

Weight (kg) 2,4

Dimensions (h x w x d in mm) 99 x 219 x 65

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission Immunity EN 55014-1, EN 61000-6-3, EN 61000-3-2

Automotive Directive EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

With the BlueSolar PWM-Pro to USB interface cable you can connect the BlueSolar PWM-Pro to your computer.

The 12l Dewhot Ecodew white powder coated gas water heater is suitable for a bathroom with a shower, bath and wash hand basin, if the bath is used occasionally. This unit is suitable for outdoor installation only.

TYPE D
For outdoor use under a cover with a flue.

Features

• Requires no electricity – flame ignition and geyser function are battery operated
• 84% energy efficiency
• Neat and compact
• Stainless steel cover
• LCD temperature display
• Flame failure safety device
• Anti-freeze function

Multiplus, Multifunctional, with intelligent power management

The Victron MultiPlus Inverter Charger is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next, to these primary functions, the MultiPlus has several advanced features, as outlined below.

Two AC Outputs

The main output has no-break functionality. The Victron MultiPlus Inverter Charger takes over the supply to the connected loads in the event of a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output (second output available on models rated at 3kVA and more).

Virtually unlimited power thanks to parallel operation

Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity.

Three phase capability

In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54 kVA three-phase inverter and 1260 A charger can be built.

Split phase options

Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30 kW / 36 kVA of split phase power. Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.

PowerControl – Dealing with limited generator, shoreside or grid power

The Victron MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist – Boosting the capacity of shore or generator power

This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging

The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the Victron MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.

System configuring has never been easier

After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

Victron Energy 100A MPPT Solar Charge Controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.

Input voltage range and frequency 180-265 VAC 45-65 Hz

Efficiency 93%

No load power consumption 0.5W

Charge voltage ‘absorption’ Normal: 14,4V

High: 14,7V

Li-ion: 14,2V

Charge voltage ‘float’ Normal: 13,8V

High: 13,8V

Li-ion: 13,5V

Charge voltage ‘storage’ Normal: 13,2V

High: 13,2V

Li-ion: 13,5V

Charge current, normal mode 13A

Charge current, LOW 4A

Charge algorithm 5-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +60°C (full rated output up to 40°C) Derate 3% per °C above 40°C

Humidity Up to 100%

Start interrupt option (Si) Short circuit proof, current limit 0,5 A

(12/25 and 24/12 models only) Output voltage: max one volt lower than main output

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery-connection Black and red cable of 1,5 meter

230 V AC-connection Cable of 1,5 meter with CEE 7/7 plug

Protection category IP67

Weight (kg) 1,8

Dimensions (h x w x d in mm) 85 x 211 x 60

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission Immunity EN 55014-1, EN 61000-6-3, EN 61000-3-2

Automotive Directive EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Two AC inputs with integrated transfer switch
The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two
generators. The Quattro will automatically connect to the active source.
Two AC Outputs
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a
grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
computers and other electronic equipment will continue to operate without disruption.
The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge
the battery, like a water heater for example, can be connected to this output.
Virtually unlimited power thanks to parallel operation
Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output
power and 840 Amps charging capacity.
Split phase options
Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per
phase, to supply up to 30kW / 36kVA of split phase power.
Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on
www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz.
Three phase capability
Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel
connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity.
PowerControl – Dealing with limited generator, shore side or grid power
The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side
supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take
account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from
being overloaded.
PowerAssist – Boosting shore or generator power
This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the
capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will
make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When
the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.
Loss of mains detection software is available.
System configuring
– In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with
a DIP switch setting procedure.
– Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
Configurator software.
– Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar
Chargers can be configured with Assistants (dedicated software for specific applications).
On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or
tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Remote Monitoring and control
Color Control GX or other GX devices.
Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
Remote configuring
When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can
be changed remotely

Multiple use application geyser (run multiple outlets simultaneously)

The smart Dewhot 12L Constant Temperature Gas Geyser automatically adjusts itself to the water flow. With multiple outlets running simultaneously your water temperature will always remain hot and constant regardless of the water demand.

TYPE B
For outdoor use under a cover with flue or indoor use with a flue

Gas Type: LPG

Features

• Requires no electricity – flame ignition and geyser function are battery operated
• Touch button temperature control
• 84% energy efficiency
• Gas efficient- reduces gas consumption according to flow demand
• Compatible with mixer taps
• Start up and geyser function operate on low water pressure
• Ventilation is required indoors
• Anti-freeze function
• Natural or LP gas compatible
• Flame failure safety device

Victron Energy 85A MPPT Solar Charge Controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.

Input voltage range 180 – 265 VAC

Charge current, normal mode 16A

Charge current, NIGHT or LOW 4 / 6 / 8 A

Efficiency 94%

No load power consumption 0.5 W

Frequency 45 – 65 Hz

Number of outputs 1

Charge voltage ‘absorption’ Normal: 28,8V High: 29,4V Li-ion: 28,4V

Charge voltage ‘float’ Normal: 27,6V High: 27,6V Li-ion: 27,0V

Charge voltage ‘storage Normal: 26,4V High: 26,4V Li-ion: 27,0V

Charge algorithm 6-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +50°C

Humidity (non-condensing) Max 98%

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery connection Screw terminals 13 mm² / AWG6

230 V AC connection Cable of 1,5 meter with CEE 7/7 plug, BS 1363 plug (UK) or AS/NZS 3112 plug (AU/NZ)

Protection category IP22

Weight 1,3 kg

Dimensions (h x w x d) 235 x 108 x 65 mm

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission EN 55014-1, EN 61000-6-3, EN 61000-3-2

Immunity EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Automotive E4-10R

Specifications :

Size : 14 x 7.6 x 4cm
Package weight : 6.3oz/178g
Rated voltage : 12V / 24V
Voltage of ending power supply : 10.8V
Recovery voltage of power supply : 10.8V
Voltage of ending charging : 14.7V or 29.4V
Rated charging current : 30A
DC output voltage : 12V or 24V
DC output current : 1A
Rated load current : 30A

Proven reliability
The full bridge plus toroidal transformer topology has proven its reliability over many years.
The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
PowerControl – Dealing with limited generator, shore side or grid power
With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist – Boosting the capacity of shore or generator power
Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
High start-up power
Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode
When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay
By default, the programmable relay is set as
an alarm relay, i.e. the relay will de-energise
in the event of an alarm or a pre-alarm
(inverter almost too hot, ripple on the input
almost too high, battery voltage almost too
low).
Remote on / off / charger on
Three pole connect

Features:
1. Small size,convenient for everyday carry.Specially designed for hiking.camping and emergency use
2. Brightness level. With max output of 1800 lumens.
3. Max beam distance up to 100 meters.
4. Effective power management circuit.
5. Battery reverse protection function
6.1 meter impact resistant.
7.Specially 2 lights designed:XPE LED for front light, COB LED for side light.

Package included:
1 x XANES 1517 XPE+COB 1800Lumens 4Modes Brightness EDC Tactical LED Flashlight
1 x Lanyard

1 x USB Cable