Our shop

BlueSolar MPPT 100/50 (12/24V – 50A)

Charge current up to 50 A and PV voltage up to 75 V, respectively 100 V
The BlueSolar Charge Controller will charge a lower nominal voltage battery with a higher nominal voltage PV array. The controllers automatically adjust to 12 V or 24 V nominal battery voltage.

Feature Highlights

• Ultra-fast Maximum Power Point Tracking (MPPT)
• Advanced Maximum Power Point Detection in case of partial shading conditions
• Load output on the small models
• BatteryLife: intelligent battery management by load shedding
• Automatic battery voltage recognition
• Flexible charge algorithm
• Over-temperature protection and power de-rating when temperature is high

All Victron Energy MPPT Charge Controllers are compatible with the Color Control GX: The Color Control GX provides intuitive control and monitoring for all products connected to it. The list of Victron products that can be connected is endless: Inverters, Multis, Quattros, MPPT 150/70, BMV-600 series, BMV-700 series, Skylla-i, Lynx Ion and even more.

Two AC inputs with integrated transfer switch
The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two
generators. The Quattro will automatically connect to the active source.
Two AC Outputs
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a
grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
computers and other electronic equipment will continue to operate without disruption.
The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge
the battery, like a water heater for example, can be connected to this output.
Virtually unlimited power thanks to parallel operation
Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output
power and 840 Amps charging capacity.
Split phase options
Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per
phase, to supply up to 30kW / 36kVA of split phase power.
Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on
www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz.
Three phase capability
Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel
connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity.
PowerControl – Dealing with limited generator, shore side or grid power
The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side
supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take
account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from
being overloaded.
PowerAssist – Boosting shore or generator power
This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the
capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will
make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When
the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.
Loss of mains detection software is available.
System configuring
– In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with
a DIP switch setting procedure.
– Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
Configurator software.
– Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar
Chargers can be configured with Assistants (dedicated software for specific applications).
On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or
tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Remote Monitoring and control
Color Control GX or other GX devices.
Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
Remote configuring
When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can
be changed remotely

Input voltage range 180 – 265 VAC

Charge current, normal mode 15A

Charge current, NIGHT or LOW 7,5 / 10 / 15 A

Efficiency 93%

No load power consumption 0.5 W

Frequency 45 – 65 Hz

Number of outputs 1

Charge voltage ‘absorption’ Normal 14,4V High: 14,7V Li-ion: 14,2V

Charge voltage ‘float’ Normal: 13,8V High: 13,8V Li-ion: 13,5V

Charge voltage ‘storage ‘ Normal: 13,2V High: 13,2V Li-ion: 13,5V

Charge algorithm 6-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +50°C

Humidity (non-condensing) Max 98%

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery connection Screw terminals 13 mm² / AWG6

230 V AC connection Cable of 1,5 meter with CEE 7/7 plug, BS 1363 plug (UK) or AS/NZS 3112 plug (AU/NZ)

Protection category IP22

Weight 1,3 kg

Dimensions (h x w x d) 235 x 108 x 65 mm

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission EN 55014-1, EN 61000-6-3, EN 61000-3-2

Immunity EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Automotive E4-10R

Victron Energy 45A MPPT Solar Charge Controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilit

Features & Benefits:

• Low power consumption
• Long lamp life
• Up to 90% energy savings
• No UV output
• Suitable replacement for a 60W Incandescent Lam
• Retrofit size

The smart solar 100/30 is designed to accept solar panel (PV) input up to 440W at 12V or 880W at 24V and has a rated charge current of 30A.

However, you should note both the open circuit voltage (Voc) and the short circuit current (Isc) of your combined solar panels and ensure this does not exceed the maximum input of the MPPT charge controller. For the 100/30 the maximum PV open circuit voltage (Voc) is 100V and the maximum PV short circuit current (Isc) is 35A.

Auto-selects 12/24V on the output. The charge controller once connected will automatically recognise your battery bank voltage.220W

Bluetooth Monitoring built-in. Remotely control and monitor the extensive features of your SmartSolar MPPT charge controller with built-in bluetooth by pairing it with your smartphone or tablet via the VictronConnect app. (Bluetooth dongle not required)

Tired of your normal plastic cooler box?
Why not try out our stylish Stainless Steel cooler boxes!

Not only do they look good but with a 65 mm foam insulation they last 10 times longer than your regular cooler box.