Input voltage range 180 – 265 VAC

Charge current, normal mode 8A

Charge current, NIGHT or LOW 4 / 6 / 8 A

Efficiency 94%

No load power consumption 0.5 W

Frequency 45 – 65 Hz

Number of outputs 1

Charge voltage ‘absorption’ Normal: 28,8V High: 29,4V Li-ion: 28,4V

Charge voltage ‘float’ Normal: 27,6V High: 27,6V Li-ion: 27,0V

Charge voltage ‘storage Normal: 26,4V High: 26,4V Li-ion: 27,0V

Charge algorithm 6-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +50°C

Humidity (non-condensing) Max 98%

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery connection Screw terminals 13 mm² / AWG6

230 V AC connection Cable of 1,5 meter with CEE 7/7 plug, BS 1363 plug (UK) or AS/NZS 3112 plug (AU/NZ)

Protection category IP22

Weight 1,3 kg

Dimensions (h x w x d) 235 x 108 x 65 mm

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission EN 55014-1, EN 61000-6-3, EN 61000-3-2

Immunity EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Automotive E4-10R

Tired of your normal plastic cooler box?
Why not try out our stylish Stainless Steel cooler boxes!

Not only do they look good but with a 65 mm foam insulation they last 10 times longer than your regular cooler box.

Multifunctional, with intelligent power management
The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge
technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the
MultiPlus has several advanced features, as outlined below.
Two AC Outputs
The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of
a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
computers and other electronic equipment will continue to operate without disruption.
The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the
battery, like a water heater for example, can be connected to this output (second output available on models rated at
3kVA and more).
Virtually unlimited power thanks to parallel operation
Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide
15kW / 18kVA output power with 420 Amps of charging capacity.
Three phase capability
In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three
strings of six parallel units a 45 kW / 54 kVA three phase inverter and 1260 A charger can be built.
Split phase options
Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per
phase, to supply up to 30 kW / 36 kVA of split phase power.
Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on
www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.
PowerControl – Dealing with limited generator, shore side or grid power
The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side
supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore
current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus
preventing the generator or shore supply from being overloaded.
PowerAssist – Boosting the capacity of shore or generator power
This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the
capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will
make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When
the load reduces, the spare power is used to recharge the battery.
Four stage adaptive charger and dual bank battery charging
The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software.
The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage
for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger
datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second
battery using an independent trickle charge output intended for a main engine or generator starter battery.
System configuring has never been easier
After installation, the MultiPlus is ready to go.
If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even
parallel and 3-phase operation can be programmed with DIP switches: no computer needed!
Alternatively, VE.Net can be used instead of the DIP switches.
And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several
new, advanced, features

SUNSYNK-8.8KW

FEATURES

Input voltage range 180 – 265 VAC

Charge current, normal mode 15A

Charge current, NIGHT or LOW 7,5 / 10 / 15 A

Efficiency 93%

No load power consumption 0.5 W

Frequency 45 – 65 Hz

Number of outputs 1

Charge voltage ‘absorption’ Normal 14,4V High: 14,7V Li-ion: 14,2V

Charge voltage ‘float’ Normal: 13,8V High: 13,8V Li-ion: 13,5V

Charge voltage ‘storage ‘ Normal: 13,2V High: 13,2V Li-ion: 13,5V

Charge algorithm 6-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +50°C

Humidity (non-condensing) Max 98%

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery connection Screw terminals 13 mm² / AWG6

230 V AC connection Cable of 1,5 meter with CEE 7/7 plug, BS 1363 plug (UK) or AS/NZS 3112 plug (AU/NZ)

Protection category IP22

Weight 1,3 kg

Dimensions (h x w x d) 235 x 108 x 65 mm

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission EN 55014-1, EN 61000-6-3, EN 61000-3-2

Immunity EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Automotive E4-10R

Interesting Facts
A dual battery system is not required as the 12v function is only used while
travelling.
Gas or 220V is used when stationary so there is no need for forced drives to charge batteries.

Your freezer
: has 75mm foam insulation which increases your cold hold over time when not switched
on compared to other freezers.
: has no moving parts inside the absorption system which makes repair and maintenance
inexpensive.
: is level sensitive hence proper levelling must be done when stationary.
: is proudly manufactured in South Africa.
: is capable of freezing to 44°C below ambient.
Example: -12°C @ 32°C
-20°C @ 20°C
: is capable of freezing 2 kg of water in 24 hours while keeping everything else frozen.
: is equipped with a gas safety valve which will cut the gas flow to the
burner in less than 60 seconds in the event of the burner flame going out.
: will only use between 400 – 500g of gas per 24 hours. A 9 kg gas bottle will last you
approximately 18 – 21 days.
: gas function is ideal for those unforeseen black outs at home.
Your Cooler Box
: has 75mm foam for maximum insulation.
: has a aluminium bin to transfer the cold all around.
: is perfect to keep you meat frozen for those long weekends.