Multiple use application geyser (run multiple outlets simultaneously)

The smart Dewhot 12L Constant Temperature Gas Geyser automatically adjusts itself to the water flow. With multiple outlets running simultaneously your water temperature will always remain hot and constant regardless of the water demand.

TYPE B
For outdoor use under a cover with flue or indoor use with a flue

Gas Type: Natural Gas

Features

• Requires no electricity – flame ignition and geyser function are battery operated
• Touch button temperature control
• 84% energy efficiency
• Gas efficient- reduces gas consumption according to flow demand
• Compatible with mixer taps
• Start up and geyser function operate on low water pressure
• Ventilation is required indoors
• Anti-freeze function
• Natural or LP gas compatible
• Flame failure safety device

Multiplus, Multifunctional, with intelligent power management

The Victron MultiPlus Inverter Charger is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next, to these primary functions, the MultiPlus has several advanced features, as outlined below.

Two AC Outputs

The main output has no-break functionality. The Victron MultiPlus Inverter Charger takes over the supply to the connected loads in the event of a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output (second output available on models rated at 3kVA and more).

Virtually unlimited power thanks to parallel operation

Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity.

Three phase capability

In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54 kVA three-phase inverter and 1260 A charger can be built.

Split phase options

Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30 kW / 36 kVA of split phase power. Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.

PowerControl – Dealing with limited generator, shoreside or grid power

The Victron MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist – Boosting the capacity of shore or generator power

This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging

The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the Victron MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.

System configuring has never been easier

After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

LiFePO4 chemistry is considered very safe even if
fully charged.
• Reliability – battery designed to operate in almost
any environment.
• Durability – life expectancy exceeding 10 years
at 25oC.
• Supports parallel bus bar connection.
• External BMS.
• Manufacturing plants comply with the
legislation in each country and with
international quality standards ISO9001 and
Qs9000.
• Residential, Business, Factory, Data Centres or
Telecoms Base Station backup.
• Solar, Wind or Hybrid Storage.
• Reduce Peak Usage Charges from the Grid

SUNSYNK-5.5KW

The Dewhot’ Stainless Steel Slim Line 16L gas water heater.

Single use application gas geyser
It is suitable for a bathroom with a bath and shower but not at the same time

TYPE D
For outdoor use under a cover with a flue

Features

• Requires no electricity – flame ignition and geyser function are battery operated
• 84% energy efficiency
• Neat and compact
• Stainless steel cover
• LCD temperature display
• Flame failure safety device
• Anti-freeze function