A MultiPlus, plus ESS (Energy Storage System) functionality
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external
currentsensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A.
The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land based off-grid applications.
It also has built-in anti-islanding functionality, and an increasingly long list of country approvals for ESS application.
Several system configurations are possible. For more detailed information see the ESS Design and configuration manual.
PowerControl and PowerAssist – Boosting the capacity of the grid or a generator
A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use
whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl
function).
PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a
limited period, the MultiPlus-II will compensate insufficient generator, shore or grid power with power from the battery.
When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The MultiPlus-II can be used in off grid as well as grid connected PV and other alternative energy systems. It is
compatible with both solar charger controllers and grid-tie inverters.
Two AC Outputs
The main output has no break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of
a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
computers and other electronic equipment will continue to operate without disruption.
The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the
battery, like a water heater for example, can be connected to this output.
Virtually unlimited power thanks to parallel and three phase operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide
25 kW / 30 kVA output power with 420 Amps charging capacity.
In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not
all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging
capacity.
On-site system configuring, monitoring and control
Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface
needed).
Several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer,
Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.
Remote configuring and monitoring
Install a Color Control GX or other GX product to connect to the internet.
Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
When connected to the internet, systems can be accessed remotely, and settings can be changed.

Features and Benefits
Discreet but powerful and long lasting, this floodlight is perfectly suited for commercial and repetitive usage,
but will also be at home in your residence or garden.
The younger brother of the Elite, this floodlight is by no means little, with a massive 1KV or 2KV surge
protection in a compact driver-on-board housing.
The design allows for auto-production which provides a truly stable, reliable and cost effective solution to
the floodlight market.
Using the newest technology, the Mesmerize Atlas range implements excellent weatherproofing and
ventilation functions called ePTEF technology.
As with most of the Mesmerize Floodlights, the Atlas comes with a 1meter H05-graded cable and an
oblique angled bracket for even easier and faster installations.
It is rated up to 25 000 hours of life and has up to 100 lumens per watt, this product carries a 2 Year Warranty.

• Rating: 200W
• Efficiency: 15.7%
• Width: 808mm
• Height: 1,580mm
• Price per Watt: (R7,736/Wp)

Input voltage range 180 – 265 VAC

Charge current, normal mode 16A

Charge current, NIGHT or LOW 4 / 6 / 8 A

Efficiency 94%

No load power consumption 0.5 W

Frequency 45 – 65 Hz

Number of outputs 3

Charge voltage ‘absorption’ Normal: 28,8V High: 29,4V Li-ion: 28,4V

Charge voltage ‘float’ Normal: 27,6V High: 27,6V Li-ion: 27,0V

Charge voltage ‘storage Normal: 26,4V High: 26,4V Li-ion: 27,0V

Charge algorithm 6-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +50°C

Humidity (non-condensing) Max 98%

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery connection Screw terminals 13 mm² / AWG6

230 V AC connection Cable of 1,5 meter with CEE 7/7 plug, BS 1363 plug (UK) or AS/NZS 3112 plug (AU/NZ)

Protection category IP22

Weight 1,3 kg

Dimensions (h x w x d) 235 x 108 x 65 mm

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission EN 55014-1, EN 61000-6-3, EN 61000-3-2

Immunity EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Automotive E4-10R

The Dewhot’ Stainless Steel Slim Line 8L Gas Water Heater.

It is suitable for an out building shower with basin, camping (and) off road trailer and for a hairdresser providing continuous hot water.

TYPE D
For outdoor use under a cover with a flue

Our light compact 5lt will make sure you have hot water wherever you are. This unit is great for camping trailers and outdoor showers. By simply connecting to a gravity fed water supply or pressure pump you can end your day with a hot shower..

TYPE A
For outdoor use under a cover or indoor use with no flue

Features

• Can be installed indoors without a flue
• 84% energy efficiency
• Ventilation is required
• Oxygen depletion sensor (Flame failure safety device)
• Starts up with very low water pressure (1 liter per minute)
• Compatible with mixer taps
• Anti-freeze function
• Requires no electricity – flame ignition and geyser function are battery operated

With the BlueSolar PWM-Pro to USB interface cable you can connect the BlueSolar PWM-Pro to your computer.

The smart solar 100/50 is designed to accept solar panel (PV) input up to 700W at 12V or 1400W at 24V and has a rated charge current of 50A.

However, you should note both the open circuit voltage (Voc) and the short circuit current (Isc) of your combined solar panels and ensure this does not exceed the maximum input of the MPPT charge controller. For the 100/50 the maximum PV open circuit voltage (Voc) is 100V and the maximum PV short circuit current (Isc) is 60A.

Auto-selects 12/24V on the output. The charge controller once connected will automatically recognise your battery bank voltage.

Bluetooth Monitoring built-in. Remotely control and monitor the extensive features of your SmartSolar MPPT charge controller with built-in bluetooth by pairing it with your smartphone or tablet via the VictronConnect app. (Bluetooth dongle not required

Multiple use application geyser (run multiple outlets simultaneously)

This smart geyser automatically adjusts itself to the water flow. With multiple outlets running simultaneously your water temperature will always remain hot and constant regardless of the water demand.

TYPE D
For outdoor use under a cover

Features

• Touch button temperature control
• 84% energy efficiency
• Gas efficient – reduces gas consumption according to flow demand
• Anti-freeze function
• Start up/ geyser function can also operate on low water pressure
• Requires no electricity – flame ignition and geyser function are battery operated
• Compatible with mixer taps
• Flame failure safety device

Features & Benefits:

• Low power consumption
• Long lamp life
• Up to 90% energy savings
• No UV output
• Suitable replacement for a 60W Incandescent Lam
• Retrofit size

BlueSolar MPPT 150/35 (12/24/48V – 70A)

Ultra-fast Maximum Power Point Tracking (MPPT)
Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT Controller will improve energy harvest by up to 30% compared to PWM Charge Controllers and by up to 10% compared to slower MPPT Controllers.

Feature Highlights

• Ultra-fast Maximum Power Point Tracking (MPPT)
• Advanced Maximum Power Point Detection in case of partial shading conditions
• Load output on the small models
• BatteryLife: intelligent battery management by load shedding
• Automatic battery voltage recognition
• Flexible charge algorithm
• Over-temperature protection and power de-rating when temperature is high

All Victron Energy MPPT Charge Controllers are compatible with the Color Control GX: The Color Control GX provides intuitive control and monitoring for all products connected to it. The list of Victron products that can be connected is endless: Inverters, Multis, Quattros, MPPT 150/70, BMV-600 series, BMV-700 series, Skylla-i, Lynx Ion and even more.

Pure sine wave inverter
Output power factor 1
Built-in MPPT solar charge controller
Selectable input voltage range for home appliances and personal computers
Selectable charging current based on applications
Configurable AC/Solar input priority via LCD setting
Compatible to mains voltage or generator power
Auto restart while AC is recovering
Overload and short circuit protection
Smart battery charger design for optimized battery
performance
Cold start function

Victron Blue Solar MPPT 75/10 10 Amp (12V/24V) Solar Charge Controller Regulator is the perfect choice for the heavy load projects. The Victron Blue Solar MPPT 75/10 10 Amp (12V/24V) Solar Charge Controller Regulator has a variety of features that ensures you get the best performance from your Solar Panels through to your batteries.

Color Control GX

All Victron Energy MPPT Charge Controllers are compatible with the Color Control GX: The Color Control GX provides intuitive control and monitoring for all products connected to it. The list of Victron products that can be connected is endless: Inverters, Multis, Quattros, MPPT 150/70, BMV-600 series, BMV-700 series, Skylla-i, Lynx Ion and even more.

VRM Online Portal

Besides monitoring and controlling products on the Color Control GX, the information is also forwarded to our free remote monitoring website: the VRM Online Portal. The portal is free of charge.

Related product:

EasySolar Minimal wiring and an all-in-one solution: the EasySolar takes power solutions one stage further, by combining an Ultra BlueSolar charge controller (MPPT), an inverter/charger and AC distribution in one enclosure.

Victron Blue Solar MPPT 75/10 10 Amp (12V/24V) Amp Solar Charge Controller Regulator

Ultra-fast Maximum Power Point Tracking (MPPT)

Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.

Load output

Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual

Battery Life: intelligent battery management

When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.

Programmable battery charge algorithm

See the software section on our website for details

Day/night timing and light dimming option

See the software section on our website for details

Programming, real-time data and history display options

– Modern Apple and Android smartphones, tablets, macbooks and other devices: see the VE.Direct Bluetooth Smart dongle an and the MPPT app discovery sheet for screenshots.

– ColorControl panel

**Note: Phone or Tablet Programming, real-time data and history display options as seen in photos require VE.Direct Bluetooth Dongle available in our Store as Optional Extra

Victron Bluesolar light PWM solar controller:

Victron’s range of PWM and MPPT charge controllers are both widely used to charge batteries with solar power.

The PWM controller is in essence a switch that connects a solar array to the battery. The result is that the voltage of the array will be pulled down to near that of the battery.

A PWM controller is not a DC to DC transformer. The PWM controller is a switch which connects the solar panel to the battery. When the switch is closed, the panel and the battery will be at nearly the same voltage. Assuming a discharged battery the initial charge voltage will be around 13 V, and assuming a voltage loss of 0,5 V over the cabling plus controller, the panel will be at Vpwm = 13,5 V.

The voltage will slowly increase with increasing state of charge of the battery. When absorption voltage is reached the PWM controller will start to disconnect and reconnect the panel to prevent overcharge (hence the name: Pulse Width Modulated controller).

Features:

– Load output with low battery voltage disconnect function.

– Lighting control function, one timer only.

– Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.

– Three stage battery charging (bulk, absorption, float), not programmable.

– Load output protected against over load and short circuit.

– Protected against reverse polarity connection of the solar array and/or battery.

Tired of your normal plastic cooler box?
Why not try out our stylish Stainless Steel cooler boxes!

Not only do they look good but with a 65 mm foam insulation they last 10 times longer than your regular cooler box.

Interesting Facts
A dual battery system is not required as the 12v function is only used while
travelling.
Gas or 220V is used when stationary so there is no need for forced drives to charge batteries.

Your freezer
: has 75mm foam insulation which increases your cold hold over time when not switched
on compared to other freezers.
: has no moving parts inside the absorption system which makes repair and maintenance
inexpensive.
: is level sensitive hence proper levelling must be done when stationary.
: is proudly manufactured in South Africa.
: is capable of freezing to 44°C below ambient.
Example: -12°C @ 32°C
-20°C @ 20°C
: is capable of freezing 2 kg of water in 24 hours while keeping everything else frozen.
: is equipped with a gas safety valve which will cut the gas flow to the
burner in less than 60 seconds in the event of the burner flame going out.
: will only use between 400 – 500g of gas per 24 hours. A 9 kg gas bottle will last you
approximately 18 – 21 days.
: gas function is ideal for those unforeseen black outs at home.
Your Cooler Box
: has 75mm foam for maximum insulation.
: has a aluminium bin to transfer the cold all around.
: is perfect to keep you meat frozen for those long weekends.

Features and Benefits
Discreet but powerful and long lasting, this floodlight is perfectly suited for commercial and repetitive usage,
but will also be at home in your residence or garden.
The younger brother of the Elite, this floodlight is by no means little, with a massive 1KV or 2KV surge
protection in a compact driver-on-board housing.
The design allows for auto-production which provides a truly stable, reliable and cost effective solution to
the floodlight market.
Using the newest technology, the Mesmerize Atlas range implements excellent weatherproofing and
ventilation functions called ePTEF technology.
As with most of the Mesmerize Floodlights, the Atlas comes with a 1meter H05-graded cable and an
oblique angled bracket for even easier and faster installations.
It is rated up to 25 000 hours of life and has up to 100 lumens per watt, this product carries a 2 Year Warranty.

Victron Energy 70A MPPT Solar Charge Controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities

• Rating: 10W
• Efficiency: 12.3%
• Width: 340mm
• Height: 240mm
• Price per Watt: (R14,924/Wp)

Input voltage range and frequency 180-265 VAC 45-65 Hz

Efficiency 93%

No load power consumption 0.5W

Charge voltage ‘absorption’ Normal: 14,4V

High: 14,7V

Li-ion: 14,2V

Charge voltage ‘float’ Normal: 13,8V

High: 13,8V

Li-ion: 13,5V

Charge voltage ‘storage’ Normal: 13,2V

High: 13,2V

Li-ion: 13,5V

Charge current, normal mode 13A

Charge current, LOW 4A

Charge algorithm 5-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +60°C (full rated output up to 40°C) Derate 3% per °C above 40°C

Humidity Up to 100%

Start interrupt option (Si) Short circuit proof, current limit 0,5 A

(12/25 and 24/12 models only) Output voltage: max one volt lower than main output

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery-connection Black and red cable of 1,5 meter

230 V AC-connection Cable of 1,5 meter with CEE 7/7 plug

Protection category IP67

Weight (kg) 1,8

Dimensions (h x w x d in mm) 85 x 211 x 60

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission Immunity EN 55014-1, EN 61000-6-3, EN 61000-3-2

Automotive Directive EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

All-in-one solar power solution
The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in
one enclosure.
The product is easy to install, with a minimum of wiring.
The solar charge controller: Blue Solar MPPT 100/50
Up to three strings of PV panels can be connected to three sets of MC4 (PV-ST01) PV connectors.
The inverter/charger: MultiPlus Compact 12/1600/70 or 24/1600/40
The MPPT charge controller and the MultiPlus Compact inverter/charger share the DC battery
cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC
power (inverter/charger) from the utility grid or a genset.
AC distribution
The AC distribution consists of a RCD (30 mA/16 A) and four AC outputs protected by two 10A and
two 16A circuit breakers.
One 16A output is controlled by the AC input: it will switch on only when AC is available.
PowerAssist
Unique PowerAssist technology protects the utility or generator supply from being overloaded by
adding extra inverter power when needed