Our shop

All-in-one solar power solution
The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in
one enclosure.
The product is easy to install, with a minimum of wiring.
The solar charge controller: Blue Solar MPPT 100/50
Up to three strings of PV panels can be connected to three sets of MC4 (PV-ST01) PV connectors.
The inverter/charger: MultiPlus Compact 12/1600/70 or 24/1600/40
The MPPT charge controller and the MultiPlus Compact inverter/charger share the DC battery
cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC
power (inverter/charger) from the utility grid or a genset.
AC distribution
The AC distribution consists of a RCD (30 mA/16 A) and four AC outputs protected by two 10A and
two 16A circuit breakers.
One 16A output is controlled by the AC input: it will switch on only when AC is available.
PowerAssist
Unique PowerAssist technology protects the utility or generator supply from being overloaded by
adding extra inverter power when needed

The low pressure geyser is the perfect solution for your off-the-grid location.
This 12LP can now run consistently off either low pressure municipal water or restricted water supplies like gravity fed tanks.

TYPE B
For outdoor use under a cover with flue or indoor use with a flue

Includes a free flexi flue. If you prefer a solid flue, this will need to be ordered separately.

Features

• Requires no electricity – flame ignition and geyser function are battery operated
• 84% energy efficiency
• Geyser can function on low and high water pressure
• Ventilation is required
• Compatible with mixer taps
• Flame failure safety device
• Anti-freeze function
• LCD temperature display

The Dewhot’ Stainless Steel Slim Line 12L gas water heater.
It is suitable for a bathroom with a shower and bath if the bath is used occasionally

TYPE D
For outdoor use under a cover with a flue

Features

• Requires no electricity – flame ignition and geyser function are battery operated
• 84% energy efficiency
• Neat and compact
• Stainless steel cover
• LCD temperature display
• Flame failure safety device
• Anti-freeze function

Feature:
Plastic shell wrapped in a layer of carbon black, feel good, non-slip.
Come with magnet and hook, Folding design, easy to use in a small space inside.
High COB LED,Low COB LED ,red led ,red sos led ,4-different lighting modes to meet your lighting needs.
LED bulbs, green energy saving and environmental protection, the use of longer time.
AA OR 18650 battery, you can use the USB cable to charge.

Product parameters:

4-mode: high/ low/ red/red sos
Size: 210 x 210 mm
Weight: 500g
Power supply: 4pcs aa or 2 pcs 18650 battery

Package Included:
1 x LED light

2 pcs 18650 battery

A MultiPlus, plus ESS (Energy Storage System) functionality
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external
currentsensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A.
The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land based off-grid applications.
It also has built-in anti-islanding functionality, and an increasingly long list of country approvals for ESS application.
Several system configurations are possible. For more detailed information see the ESS Design and configuration manual.
PowerControl and PowerAssist – Boosting the capacity of the grid or a generator
A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use
whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl
function).
PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a
limited period, the MultiPlus-II will compensate insufficient generator, shore or grid power with power from the battery.
When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The MultiPlus-II can be used in off grid as well as grid connected PV and other alternative energy systems. It is
compatible with both solar charger controllers and grid-tie inverters.
Two AC Outputs
The main output has no break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of
a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
computers and other electronic equipment will continue to operate without disruption.
The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the
battery, like a water heater for example, can be connected to this output.
Virtually unlimited power thanks to parallel and three phase operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide
25 kW / 30 kVA output power with 420 Amps charging capacity.
In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not
all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging
capacity.
On-site system configuring, monitoring and control
Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface
needed).
Several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer,
Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.
Remote configuring and monitoring
Install a Color Control GX or other GX product to connect to the internet.
Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
When connected to the internet, systems can be accessed remotely, and settings can be changed.

Proven reliability
The full bridge plus toroidal transformer topology has proven its reliability over many years.
The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
PowerControl – Dealing with limited generator, shore side or grid power
With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist – Boosting the capacity of shore or generator power
Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
High start-up power
Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode
When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay
By default, the programmable relay is set as
an alarm relay, i.e. the relay will de-energise
in the event of an alarm or a pre-alarm
(inverter almost too hot, ripple on the input
almost too high, battery voltage almost too
low).
Remote on / off / charger on
Three pole connect

Input voltage range and frequency 180-265 VAC 45-65 Hz

Efficiency 94%

No load power consumption 0.5W

Charge voltage ‘absorption’ Normal: 28,8V

High: 29,4V

Li-ion: 28,4V

Charge voltage ‘float’ Normal: 27,6V

High: 27,6V

Li-ion: 27,0V

Charge voltage ‘storage’ Normal: 26,4V

High: 26,4V

Li-ion: 27,0V

Charge current, normal mode 5A

Charge current, LOW 2A

Charge algorithm 5-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +60°C (full rated output up to 40°C) Derate 3% per °C above 40°C

Humidity Up to 100%

Start interrupt option (Si) Short circuit proof, current limit 0,5 A

(12/25 and 24/12 models only) Output voltage: max one volt lower than main output

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery-connection Black and red cable of 1,5 meter

230 V AC-connection Cable of 1,5 meter with CEE 7/7 plug

Protection category IP67

Weight (kg) 1,8

Dimensions (h x w x d in mm) 85 x 211 x 60

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission Immunity EN 55014-1, EN 61000-6-3, EN 61000-3-2

Automotive Directive EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Victron Energy 70A MPPT Solar Charge Controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities

Victron BlueSolar PWM-Light Charge Controller 48V-30A, 2 Year Warranty.

BlueSolar PWM-Light

• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery.
• Day/night timing options: see manual for details

Features:

• Load output with low battery voltage disconnect function.
• Lighting control function, one timer only.
• Seven segment display for quick and easy setting of the load output functionality, including timer setting.
• Three stage battery charging (bulk, absorption, float), not programmable.
• Load output protected against over load and short circuit.
• Protected against reverse polarity connection of the solar array and/or battery

Victron Energy 100A MPPT Solar Charge Controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.

The Dewhot’ Stainless Steel Slim Line 8L Gas Water Heater.

It is suitable for an out building shower with basin, camping (and) off road trailer and for a hairdresser providing continuous hot water.

TYPE D
For outdoor use under a cover with a flue