Our shop

Proven reliability
The full bridge plus toroidal transformer topology has proven its reliability over many years.
The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
PowerControl – Dealing with limited generator, shore side or grid power
With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist – Boosting the capacity of shore or generator power
Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
High start-up power
Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode
When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay
By default, the programmable relay is set as
an alarm relay, i.e. the relay will de-energise
in the event of an alarm or a pre-alarm
(inverter almost too hot, ripple on the input
almost too high, battery voltage almost too
low).
Remote on / off / charger on
Three pole connect

Multiple use application geyser (run multiple outlets simultaneously)

The smart Dewhot 12L Constant Temperature Gas Geyser automatically adjusts itself to the water flow. With multiple outlets running simultaneously your water temperature will always remain hot and constant regardless of the water demand.

TYPE B
For outdoor use under a cover with flue or indoor use with a flue

Gas Type: LPG

Features

• Requires no electricity – flame ignition and geyser function are battery operated
• Touch button temperature control
• 84% energy efficiency
• Gas efficient- reduces gas consumption according to flow demand
• Compatible with mixer taps
• Start up and geyser function operate on low water pressure
• Ventilation is required indoors
• Anti-freeze function
• Natural or LP gas compatible
• Flame failure safety device

Handy Light

1 x Unit

1 x AC Wire

1 x Solar Panel

3 x LED Lights

Indoor and Outdoor Use

15-30H Light

SinusMax – Superior engineering
Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications.
The design criteria have been to produce a true sine wave inverter with optimised efficiency but without
compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact
dimensions, light in weight and capable of supplying power, problem-free, to any load.

Extra start-up power
A unique feature of the SinusMax technology is very high start-up power. Conventional high frequency
technology does not offer such extreme performance. Phoenix inverters, however, are well suited to power up
difficult loads such as refrigeration compressors, electric motors and similar appliances.

Virtually unlimited power thanks to parallel and 3-phase operation capability
Up to 6 units inverters can operate in parallel to achieve higher power output. Six 24/5000 units, for example,
will provide 24kW / 30kVA output power. Operation in 3-phase configuration is also possible.

To transfer the load to another AC source: the automatic transfer switch
If an automatic transfer switch is required we recommend using the MultiPlus inverter/charger instead. The
switch is included in these products and the charger function of the MultiPlus can be disabled. Computers and
other electronic equipment will continue to operate without disruption because the MultiPlus features a very
short switchover time (less than 20 milliseconds).

Computer interface
All models have a RS-485 port. All you need to connect to your PC is our MK2 interface (see under accessories).
This interface takes care of galvanic isolation between the inverter and the computer, and converts from RS-485
to RS-232. A RS-232 to USB conversion cable is also available. Together with our VEConfigure software, which
can be downloaded free of charge from our website, all parameters of the inverters can be customised. This
includes output voltage and frequency, over and under voltage settings and programming the relay. This relay
can for example be used to signal several alarm conditions, or to start a generator. The inverters can also be
connected to VENet, the new power control network of Victron Energy, or to other computerised monitoring
and control systems.

New applications of high power inverters
The possibilities of paralleled high power inverters are truly amazing. For ideas, examples and battery capacity
calculations please refer to our book “Energy Unlimited” (available free of charge from Victron Energy and
downloadable from www.victronenergy.com

This high quality IP67 rated connector is designed to protect solar panels from current backflow.

This is a recommended investment to protect your valuable investment in solar panels.

Feature:

-30A in-line Diode Connector Solar Panel Cable Connectors

– Practical connector used between Solar panel and switch box to prevent the reversal of current.

– Contacts for the connector are copper, coated with tin for easy solder adhesion. Each end nuts comes with rubber bushings for air tightening.

– This MC4 connector is rated as IP67. IP (Ingress Protection) ratings the first numeral refers to the level of dust resistance and the second numeral refers to the level of water resistance.

– Diode built in the connector

– TUV-approved Connector head

pecification: Brand new Rated voltage: 12V Working voltage 6-15V Rated current: 1.2A Maximum head: 5m Maximum flow: 600L/H Size: approx. 10.8 x 4cm(H x W)

Input voltage 230 VAC

Efficiency 95%

Standby power consumption 0,5 W

Minimum battery voltage Starts charging from down to 0V

Charge voltage ‘absorption’ Normal: 28,8 V

High: 29,4 V

Li-ion: 28,4 V

Charge voltage ‘float’ Normal: 27,6 V

High: 27,6 V

Li-ion: 27,0 V

Charge voltage ‘storage’ Normal: 26,4 V

High: 26,4 V

Li-ion: 27,0 V

Charge current 13 A

Low current mode 4 A

Temperature compensation 32 mV/ºC

(lead-acid batteries only)

Can be used as power supply Yes

Back current drain 0,7 Ah/month (1 mA)

Protection Reverse polarity Output short circuit

Over temperature

Operating temp. range -40 to +60°C (full rated output up to 30°C)

(cables retain flexibility at low temperature)

Humidity (non-condensing) Max 95%

ENCLOSURE

Battery-connection Black and red cable of 1,5 meter

230 V AC-connection Cable of 1,5 meter with

CEE 7/7, BS 1363 plug (UK) or AS/NZS 3112 plug

Protection category IP65 (splash and dust proof)

Weight IP65 12V 25A 24V 13A: 1,9kg

Other: 0,9kg

Dimensions (h x w x d) 24V 13A: 75x140x240mm

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission EN 55014-1, EN 61000-6-3, EN 61000-3-2

Immunity EN 55014-2,EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Interesting Facts
A dual battery system is not required as the 12v function is only used while
travelling.
Gas or 220V is used when stationary so there is no need for forced drives to charge batteries.

Your freezer
: has 75mm foam insulation which increases your cold hold over time when not switched
on compared to other freezers.
: has no moving parts inside the absorption system which makes repair and maintenance
inexpensive.
: is level sensitive hence proper levelling must be done when stationary.
: is proudly manufactured in South Africa.
: is capable of freezing to 44°C below ambient.
Example: -12°C @ 32°C
-20°C @ 20°C
: is capable of freezing 2 kg of water in 24 hours while keeping everything else frozen.
: is equipped with a gas safety valve which will cut the gas flow to the
burner in less than 60 seconds in the event of the burner flame going out.
: will only use between 400 – 500g of gas per 24 hours. A 9 kg gas bottle will last you
approximately 18 – 21 days.
: gas function is ideal for those unforeseen black outs at home.
Your Cooler Box
: has 75mm foam for maximum insulation.
: has a aluminium bin to transfer the cold all around.
: is perfect to keep you meat frozen for those long weekends.

• Rating: 460W
• Efficiency: 20.7%
• Width: 1,052mm
• Height: 2,112mm

The PowAR Snap – Fastener Clip fits into place on the module frame. Once attached to the module, the four clips simply snap into place on your structural support.

No tools are required for installation, however, a setting tool is available for convenient removal of the fastener from the support.

QUICK
Fastening and grounding in a single operation.
Up to 5 times faster than a clamp.

EASY TO USE
Tool-free set up.
Designed for non-qualified workers – allowing minimal training.
Intuitive: the “click” signals the function is complete.
Friendly: no need for climbing on structure, panels can be inserted from underneath the array.

DC combiner boxes are for connecting parallel PV strings into your MPPT. The box includes several features that reduces the amount of separate components you need to install.

The box offers isolation between the DC voltages that are generated by the PV modules and the solar installation allowing for safety while working or maintaining the system.
With fusing and short circuit protection the PV modules and components can operate optimally with lightning protection included. Combining multiple series strings from the PV modules the unit allows for a single parallel connection to the MPPT charge controller.
Positive and negative poles of each PV string are equipped with special fuse wire, which protects the PV string from fault. It also uses matchable fuse holder and fuse wire to reduce later maintenance cost and guarantee safety
The unit uses photovoltaic HV lightning protector to carry out protection to the positive pole-to-ground and negative pole-to-ground of bus after combination