These water proof Y-Connectors make it possible to parallel wire PV modules with MC4 (locking-type) output wires. This branch plug has (2)Male to (1)Female.

Victron Bluesolar light PWM solar controller:

Victron’s range of PWM and MPPT charge controllers are both widely used to charge batteries with solar power.

The PWM controller is in essence a switch that connects a solar array to the battery. The result is that the voltage of the array will be pulled down to near that of the battery.

A PWM controller is not a DC to DC transformer. The PWM controller is a switch which connects the solar panel to the battery. When the switch is closed, the panel and the battery will be at nearly the same voltage. Assuming a discharged battery the initial charge voltage will be around 13 V, and assuming a voltage loss of 0,5 V over the cabling plus controller, the panel will be at Vpwm = 13,5 V.

The voltage will slowly increase with increasing state of charge of the battery. When absorption voltage is reached the PWM controller will start to disconnect and reconnect the panel to prevent overcharge (hence the name: Pulse Width Modulated controller).

Features:

– Load output with low battery voltage disconnect function.

– Lighting control function, one timer only.

– Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.

– Three stage battery charging (bulk, absorption, float), not programmable.

– Load output protected against over load and short circuit.

– Protected against reverse polarity connection of the solar array and/or battery.

L051100-A Energy Storage System is consisted of 2 sets of M025100-A modules manufactured by

Sunsynk. In each M025100-A, there are 8 pcs of 100 Ah LFP cell originated from CATL. The overall

system also provides standard communication port, i.e. CAN and RS485, to monitor the working status

and communicate with upper machine as well as the Power Conversion System (PCS) in front.

The system makes use of photovoltaic technology and a unique PTC AC/DC element to heat the water
in the geyser. This differs from the traditional thermal hot water systems where water is cycled from a
collector through pipes to the hot water cylinder by either making use of a 220V pump, 12V pump or
thermo siphoning.
Advantages over thermal hot water systems are as follows:
Any existing geyser can be converted
No Additional plumbing is required
No pumps necessary to circulate water
No risk of damaged panels in frost prone areas
The water temperature can be controlled on very hot summer days – reduced risk of overheating
problems
Suitable in all water conditions
Suitable in areas where the geyser is not situated near the panels
Modular system – can be expanded to build off-grid power system for the home

BlueSolar PWM-Light 12/24V-5A

Victron Bluesolar light PWM solar controller:

Victron’s range of PWM and MPPT charge controllers are both widely used to charge batteries with solar power.

The PWM controller is in essence a switch that connects a solar array to the battery. The result is that the voltage of the array will be pulled down to near that of the battery.

A PWM controller is not a DC to DC transformer. The PWM controller is a switch which connects the solar panel to the battery. When the switch is closed, the panel and the battery will be at nearly the same voltage. Assuming a discharged battery the initial charge voltage will be around 13 V, and assuming a voltage loss of 0,5 V over the cabling plus controller, the panel will be at Vpwm = 13,5 V.

The voltage will slowly increase with increasing state of charge of the battery. When absorption voltage is reached the PWM controller will start to disconnect and reconnect the panel to prevent overcharge (hence the name: Pulse Width Modulated controller).

Features:

– Load output with low battery voltage disconnect function.

– Lighting control function, one timer only.

– Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.

– Three stage battery charging (bulk, absorption, float), not programmable.

– Load output protected against over load and short circuit.

– Protected against reverse polarity connection of the solar array and/or battery.

Day/night timing options:

Description

• The polycarbonate housing has an aluminium heat sink that disperses heat that damages the Sanan Optoelectronic LED chips.
• These individually mounted LED chips are covered with a frosted lens that diffuses the light to provide a 120º beam angle for a more uniform and comfortable spread of light.
• The slim design of the entire luminaire means that bulkhead installations are not a problem, and the magnetic backing means mounting is a breeze.
• The Ingress Protection rating of IP44 means this luminaire is well suited to bathrooms or verandas as well as commercial kitchens or freezers with an operating temperature of -20ºC ? 50ºC.
• Reliably tested for up to 30 000 hours, this product comes with a 2-year warranty.

Additional information

Weight 0.06 kg

Dimensions 9 x 6 x 4 cm

Multiple use application geyser (run multiple outlets simultaneously)

This smart geyser automatically adjusts itself to the water flow. With multiple outlets running simultaneously your water temperature will always remain hot and constant regardless of the water demand.

TYPE D
For outdoor use under a cover

Features

• Touch button temperature control
• 84% energy efficiency
• Gas efficient – reduces gas consumption according to flow demand
• Anti-freeze function
• Start up/ geyser function can also operate on low water pressure
• Requires no electricity – flame ignition and geyser function are battery operated
• Compatible with mixer taps
• Flame failure safety device

SUNSYNK-5.5KW

Input voltage range and frequency 180-265 VAC 45-65 Hz

Efficiency 96%

No load power consumption 0.5W

Charge voltage ‘absorption’ Normal: 28,8V

High: 29,4V

Li-ion: 28,4V

Charge voltage ‘float’ Normal: 27,6V

High: 27,6V

Li-ion: 27,0V

Charge voltage ‘storage’ Normal: 26,4V

High: 26,4V

Li-ion: 27,0V

Charge current, normal mode 8A

Charge current, LOW 3A

Charge algorithm 5-stage adaptive

Can be used as power supply Yes

Protection Battery reverse polarity (fuse) Output short circuit Over temperature

Operating temp. range -20 to +60°C (full rated output up to 40°C) Derate 3% per °C above 40°C

Humidity Up to 100%

Start interrupt option (Si) Short circuit proof, current limit 0,5 A

(12/25 and 24/12 models only) Output voltage: max one volt lower than main output

ENCLOSURE

Material & Colour Aluminium (blue RAL 5012)

Battery-connection Black and red cable of 1,5 meter

230 V AC-connection Cable of 1,5 meter with CEE 7/7 plug

Protection category IP67

Weight (kg) 2,4

Dimensions (h x w x d in mm) 99 x 219 x 65

STANDARDS

Safety EN 60335-1, EN 60335-2-29

Emission Immunity EN 55014-1, EN 61000-6-3, EN 61000-3-2

Automotive Directive EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Multiplus, Multifunctional, with intelligent power management

The Victron MultiPlus Inverter Charger is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next, to these primary functions, the MultiPlus has several advanced features, as outlined below.

Two AC Outputs

The main output has no-break functionality. The Victron MultiPlus Inverter Charger takes over the supply to the connected loads in the event of a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output (second output available on models rated at 3kVA and more).

Virtually unlimited power thanks to parallel operation

Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity.

Three phase capability

In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54 kVA three-phase inverter and 1260 A charger can be built.

Split phase options

Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30 kW / 36 kVA of split phase power. Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.

PowerControl – Dealing with limited generator, shoreside or grid power

The Victron MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist – Boosting the capacity of shore or generator power

This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging

The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the Victron MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.

System configuring has never been easier

After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

Victron Energy 60A MPPT Solar Charge Controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.

Victron Energy 45A MPPT Solar Charge Controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilit

Proven reliability
The full bridge plus toroidal transformer topology has proven its reliability over many years.
The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
PowerControl – Dealing with limited generator, shore side or grid power
With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist – Boosting the capacity of shore or generator power
Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
High start-up power
Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode
When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay
By default, the programmable relay is set as
an alarm relay, i.e. the relay will de-energise
in the event of an alarm or a pre-alarm
(inverter almost too hot, ripple on the input
almost too high, battery voltage almost too
low).
Remote on / off / charger on
Three pole connect

BlueSolar MPPT 100/50 (12/24V – 50A)

Charge current up to 50 A and PV voltage up to 75 V, respectively 100 V
The BlueSolar Charge Controller will charge a lower nominal voltage battery with a higher nominal voltage PV array. The controllers automatically adjust to 12 V or 24 V nominal battery voltage.

Feature Highlights

• Ultra-fast Maximum Power Point Tracking (MPPT)
• Advanced Maximum Power Point Detection in case of partial shading conditions
• Load output on the small models
• BatteryLife: intelligent battery management by load shedding
• Automatic battery voltage recognition
• Flexible charge algorithm
• Over-temperature protection and power de-rating when temperature is high

All Victron Energy MPPT Charge Controllers are compatible with the Color Control GX: The Color Control GX provides intuitive control and monitoring for all products connected to it. The list of Victron products that can be connected is endless: Inverters, Multis, Quattros, MPPT 150/70, BMV-600 series, BMV-700 series, Skylla-i, Lynx Ion and even more.

Solar Mounting Component

Tired of your normal plastic cooler box?
Why not try out our stylish Stainless Steel cooler boxes!

Not only do they look good but with a 65 mm foam insulation they last 10 times longer than your regular cooler box.

Size : 168mm x 92mm x 41.5mm
Net Weight : 320g

Proven reliability
The full bridge plus toroidal transformer topology has proven its reliability over many years.
The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
PowerControl – Dealing with limited generator, shore side or grid power
With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist – Boosting the capacity of shore or generator power
Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
High start-up power
Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode
When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay
By default, the programmable relay is set as
an alarm relay, i.e. the relay will de-energise
in the event of an alarm or a pre-alarm
(inverter almost too hot, ripple on the input
almost too high, battery voltage almost too
low).
Remote on / off / charger on
Three pole connect

The BlueSolar Charger series uses Pulse Width Modulation (PWM) charge voltage control combined with a multistage charge control algorithm. This leads to superior charging and enhanced battery performance. The filtered PWM power control system uses highly efficient and reliable power MOSFET transistors.

Fully automatic temperature compensation of charge voltage is available to improve charge control and battery performance.

Features

· Internal temperature sensor.

· Three-stage battery charging [bulk – absorption – float], not programmable

· Protected against overcurrent.
·
Load output protected against overload and short circuit.
·
Protected against reverse polarity connection of the solar panels and/or battery.
·
Load output with low battery voltage disconnect function.
· Intelligent software control.
·
PWM charging mode.
· Two digit seven segment display for the quick and easy setting of the load output functionality, incl. timer setting.
· Day/night timing options – See manual for details