Inverters

  • AXPERT V OFF-GRID INVERTER 1000W 12V

    R3,243.00

    GENERAL FEATURES
    Pure sine wave solar inverter
    Output power factor 1
    Selectable high power charging current
    Built-in 50A PWM solar charger with wide DC input range
    Selectable input voltage range for home appliances and personal
    computers
    Configurable AC/Solar input priority via LCD setting
    Compatible to AC mains or generator power
    Auto restart while AC is recovering
    Overload and short circuit protection
    Smart battery charger design for optimised battery performance
    Cold start function
    Optional anti-dust kit

    View product
  • AXPERT V OFF-GRID INVERTER 2400W 24V

    R5,433.75

    GENERAL FEATURES
    Pure sine wave solar inverter
    Grid assisted, off-grid hybrid solar inverter:
    PV + Battery / Battery only / Battery + Grid / PV + Battery + Grid
    Selectable high power charging current
    Wide DC input range
    Selectable input voltage range for home appliances and personal
    computers
    Configurable AC/Solar input priority via LCD setting
    Compatible to mains voltage or generator power
    Auto restart while AC is recovering
    Overload and short circuit protection
    Smart battery charger design for optimised battery performance
    Cold start function

    View product
  • BlueSolar PWM-Pro to USB interface cable

    R220.05

    With the BlueSolar PWM-Pro to USB interface cable you can connect the BlueSolar PWM-Pro to your computer.

    View product
  • EasySolar 12/1600/70-16 MPPT 100/50

    R25,249.81

    All-in-one solar power solution
    The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in
    one enclosure.
    The product is easy to install, with a minimum of wiring.
    The solar charge controller: Blue Solar MPPT 100/50
    Up to three strings of PV panels can be connected to three sets of MC4 (PV-ST01) PV connectors.
    The inverter/charger: MultiPlus Compact 12/1600/70 or 24/1600/40
    The MPPT charge controller and the MultiPlus Compact inverter/charger share the DC battery
    cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC
    power (inverter/charger) from the utility grid or a genset.
    AC distribution
    The AC distribution consists of a RCD (30 mA/16 A) and four AC outputs protected by two 10A and
    two 16A circuit breakers.
    One 16A output is controlled by the AC input: it will switch on only when AC is available.
    PowerAssist
    Unique PowerAssist technology protects the utility or generator supply from being overloaded by
    adding extra inverter power when needed

    View product
  • EasySolar 24/1600/40-16 MPPT 100/50

    R25,250.12

    All-in-one solar power solution
    The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in
    one enclosure.
    The product is easy to install, with a minimum of wiring.
    The solar charge controller: Blue Solar MPPT 100/50
    Up to three strings of PV panels can be connected to three sets of MC4 (PV-ST01) PV connectors.
    The inverter/charger: MultiPlus Compact 12/1600/70 or 24/1600/40
    The MPPT charge controller and the MultiPlus Compact inverter/charger share the DC battery
    cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC
    power (inverter/charger) from the utility grid or a genset.
    AC distribution
    The AC distribution consists of a RCD (30 mA/16 A) and four AC outputs protected by two 10A and
    two 16A circuit breakers.
    One 16A output is controlled by the AC input: it will switch on only when AC is available.
    PowerAssist
    Unique PowerAssist technology protects the utility or generator supply from being overloaded by
    adding extra inverter power when needed

    View product
  • EasySolar 24/3000/70 MPPT 150/70 Color Control

    R37,051.32

    The all-in-one solar power solution
    The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution
    in one enclosure.
    The product is easy to install, with a minimum of wiring.
    Color Control panel
    Two outstanding functions:
    – Prioritizes battery charging by the MPPT charge controller
    – Connects to the internet, enabling remote monitoring (VRM website) and remote control.
    AC distribution
    The AC distribution consists of a RCD (30mA / 63A) and four AC outputs protected by two 10A
    and two 16A circuit breakers.
    An additional 16A output is controlled by the AC input: it will switch on only when AC is available.
    PowerAssist
    Unique PowerAssist technology protects the utility or generator supply from being overloaded
    by adding extra inverter power when needed

    View product
  • EasySolar 48/5000/70 MPPT 150/100 Color Control

    R59,831.30

    The all-in-one solar power solution
    The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution
    in one enclosure.
    The product is easy to install, with a minimum of wiring.
    Color Control panel
    Two outstanding functions:
    – Prioritizes battery charging by the MPPT charge controller
    – Connects to the internet, enabling remote monitoring (VRM website) and remote control.
    AC distribution
    The AC distribution consists of a RCD (30mA / 63A) and four AC outputs protected by two 10A
    and two 16A circuit breakers.
    An additional 16A output is controlled by the AC input: it will switch on only when AC is available.
    PowerAssist
    Unique PowerAssist technology protects the utility or generator supply from being overloaded
    by adding extra inverter power when needed

    View product
  • Growatt SPF 3000TL HVM-24 3kVA/3kW 24V Hybrid Inverter with WiFi

    R8,280.00

    Growatt SPF 3000-5000TL HVM series off grid solar inverter is integrated with a MPPT solar charge controller, Transformerless design provides reliable power conversion in compact size.

    • Integrated MPPT charge controller.
    • Configurable grid or solar input priority.
    • WIFI remote monitoring.
    • Parallel for scalability.
    View product
  • Growatt SPF 3000TL HVM-48 3kVA/3kW 48V Hybrid Inverter with WiFi

    Growatt SPF 3000-5000TL HVM series off grid solar inverter is integrated with a MPPT solar charge controller, Transformerless design provides reliable power conversion in compact size.

    • Integrated MPPT charge controller.
    • Configurable grid or solar input priority.
    • WIFI remote monitoring.
    • Parallel for scalability.
    View product
  • Jaguar 720W 1200VA 12V Simulated Sinewave, PWM Charger

    R2,228.13

    GENERAL FEATURES
    Simulated sine wave inverter
    Wide input voltage range
    10 A or 20 A standard AC charging current
    Desktop and wall-mounting for flexible display
    LCD display for comprehensive information
    Overload, short circuit and polarity reverse protection
    Built-in 50A solar charger

    View product
  • KODAK 3.0kW Single phase, Grid tied Solar Inverter

    R10,479.96

    Part No: i3.0 Inverters – Main Units

    • Rating: 3,000W
    • Phases: 1

    KODAK 3.0kW Solar Inverter

    • Muti-working mode fully compatible with new AS4777.2:2015 standard
    • Easy installation: Integrate with export power control function and DRM function.
    • Max. Efficiency over 97.8% MPPT efficiency over 99.5%
    • Ultra wide input voltage range
    • Dual MPPT design with precise MPPT algorithm
    • Compact and light design for one-person easy installation
    • IP65 visually pleasing for domestic environment
    • RS 485WiFi/GPRS(optional)interface
    • Numerous protection functions
    • WiFi and monitoring app available
    • High switching frequency design to be more reliable and efficient.
    • Ultra low harmonic THDi<1.5%
    • Export Limitation built in – Requires CT clamp (sold separately) – NOW G100 COMPLIANT
    View product
  • KODAK 3.0kW Solar Hybrid Inverter

    R15,076.01

    All NEW KODAK Intelligent Hybrid PV Inverter

    • Dual MPPT

    • Off-grid backup function

    • Export Control

    • UPS function

    • Intelligent EMS function

    • Integrated BMS

    • Smart battery SOC detection – Compatible with various 48V batteries such as Pylontech

    • Multiple protection functions

    • CAN, RS485, WiFi/LAN/GRPS (Optional)

    • 5 product warranty

    View product
  • KODAK 3.6kW Solar Hybrid Inverter

    All NEW KODAK Intelligent Hybrid PV Inverter

    • Dual MPPT

    • Off-grid backup function

    • Export Control

    • UPS function

    • Intelligent EMS function

    • Integrated BMS

    • Smart battery SOC detection – Compatible with various 48V batteries such as Pylontech

    • Multiple protection functions

    • CAN, RS485, WiFi/LAN/GRPS (Optional)

    • 5 product warranty

    View product
  • KODAK 3kW 24V Solar Off-Grid-plus Inverter with UPS

    R11,893.59

    KODAK Off-grid inverter with UPS

    In rural or end-of-line locations, the AC grid voltage can fluctuate across a wide range. Voltage that is sufficently far from the nominal 230V can cause applicances to run much less efficiently, or make them unable to function.

    Most other inverters that are capable of running in Island Mode simply pass through the variable grid voltage and only produce a smooth 230V supply in the event of a grid failure.

    Kodak’s King Off-Grid inverter is perfect for areas where grid electricity is less stable because it produces smooth 230V AC at all times, whether the grid is available or not.

    This is great for efficient running of applicances, but crucial for an uninterrupted supply for important loads such as servers or ATMs.

    Operates at 24V, so an ideal match with the Pylon US2500 24V model.

    • Built-in Bluetooth for mobile monitoring Detachable LCD control module with multiple communications (Android App is available)
    • Supports USB On-the-Go function
    • Reserved communication port for BMS (RS485, CAN-BUS or RS232)
    • Configurable AC/PV output usage timer and prioritization
    • Parallel operation up to 9 units
    • Robust UPS (uninterrupted power supply) for essential loads with zero transfer time

    Note: The Kodak King inverter has a CAN-bus port included, which means a direct connection to Plyontech batteries is possible. Therefore no other control module, such as the ICC, is needed.

    View product
  • KODAK 4.6kW Solar Hybrid Inverter

    All NEW KODAK Intelligent Hybrid PV Inverter

    • Dual MPPT

    • Off-grid backup function

    • Export Control

    • UPS function

    • Intelligent EMS function

    • Integrated BMS

    • Smart battery SOC detection – Compatible with various 48V batteries such as Pylontech

    • Multiple protection functions

    • CAN, RS485, WiFi/LAN/GRPS (Optional)

    • 5 product warranty

    View product
  • KODAK 5KW 48V Solar Off-Grid-PLUS(king) Inverter with UPS

    R13,968.34

    KODAK Off-grid inverter with UPS

    In rural or end-of-line locations, the AC grid voltage can fluctuate across a wide range. Voltage that is sufficently far from the nominal 230V can cause applicances to run much less efficiently, or make them unable to function.

    Most other inverters that are capable of running in Island Mode simply pass through the variable grid voltage and only produce a smooth 230V supply in the event of a grid failure.

    Kodak’s King Off-Grid inverter is perfect for areas where grid electricity is less stable because it produces smooth 230V AC at all times, whether the grid is available or not.

    This is great for efficient running of applicances, but crucial for an uninterrupted supply for important loads such as servers or ATMs.

    • Built-in Bluetooth for mobile monitoring Detachable LCD control module with multiple communications (Android App is available)
    • Supports USB On-the-Go function
    • Reserved communication port for BMS (RS485, CAN-BUS or RS232)
    • Configurable AC/PV output usage timer and prioritization
    • Parallel operation up to 9 units
    • Robust UPS (uninterrupted power supply) for essential loads with zero transfer time

    Note: The Kodak King inverter has a CAN-bus port included, which means a direct connection to Plyontech batteries is possible. Therefore no other control module, such as the ICC, is needed

    View product
  • KODAK Solar Off-Grid Inverter 1.5kW 24V

    R9,323.75

    The OG 1.24 is ideal as an affordable and fully functional centre of your off-grid system.

    Wide MPP voltage range makes DC string design with your choice of module easy.

    Best suited to smaller domestic systems where no parallel operation is needed.

    Operates at 24V, so an ideal match with the Pylon UP2500 24V model and Giter G2500-24 24V model.

    • Removable LCD control module with multiple communications servers and ATM
    • Built-in Bluetooth for mobile monitoring (Android App is available)
    • Replaceable fan design for ease of maintenance
    • Supply load from Grid or PV, even battery is not available
    • Configurable AC/PV output usage timer and prioritization
    • Selectable high power charging current
    • Selectable input voltage range for home appliances and personal computers
    • Compatible to Utility Mains or generator input Auto restart while AC is recovering
    • Cold start function
    View product
  • KODAK Solar Off-Grid Inverter 10kW 48V

    R29,741.59

    Weight:20 kgRated Power:10,000 WMin PPT Voltage:90 VMax PPT Voltage:450 VDC Startup Voltage:90 VDC Shutdown Voltage:90 VMax Input Voltage:500 VMax DC Power:10,000 WMax AC Power (5 Minutes):11,000 WSurge AC Power (1 Second):20,000 WMax DC Current:36 AMax DC Inputs:2Has DC Fuses:0Connector:MC4  Included Connectors:2Euro Efficiency:93 %Transformer:NoneMPPT Quantity :2Has Integrated DC Switch:NoWarranty:3 years

    View product
  • KODAK Solar Off-Grid Inverter 5.6kW 48V

    R16,400.09

    View product
  • KODAK Solar Off-Grid Inverter King with UPS 3kW 24V

    R11,992.14

    KODAK Off-grid inverter with UPS

    In rural or end-of-line locations, the AC grid voltage can fluctuate across a wide range. Voltage that is sufficently far from the nominal 230V can cause applicances to run much less efficiently, or make them unable to function.

    Most other inverters that are capable of running in Island Mode simply pass through the variable grid voltage and only produce a smooth 230V supply in the event of a grid failure.

    Kodak’s King Off-Grid inverter is perfect for areas where grid electricity is less stable because it produces smooth 230V AC at all times, whether the grid is available or not.

    This is great for efficient running of applicances, but crucial for an uninterrupted supply for important loads such as servers or ATMs.

    Operates at 24V, so an ideal match with the Pylon US2500 24V model.

    • Built-in Bluetooth for mobile monitoring Detachable LCD control module with multiple communications (Android App is available)
    • Supports USB On-the-Go function
    • Reserved communication port for BMS (RS485)
    • Configurable AC/PV output usage timer and prioritization
    • Parallel operation up to 9 units
    • Robust UPS (uninterrupted power supply) for essential loads with zero transfer time

    View a complete range of Kodak and Pylon hybid storage systems and design a bespoke solution in seconds using Quick Quote.

    Please note: Because of the low Voltage MPPT on this unit. It works best with 2x 72 cell modules or 3x 60 cell modules per string. Any more could cause an over voltage on the MPPT and damage it.
    Included in Kit
    KIT-OGPLUS3.24 KODAK OG-PLUS3.24 3kW 24V Off-Grid Kit
    KIT-OGPLUS3.24-BU KODAK OG-PLUS3.24 3kW 24V Back-Up Kit
    View product
  • KODAK Solar Off-Grid Inverter MAX 7.2kW 48V

    R22,706.06

    The KODAK OG-7.2 Max Off-Grid inverter is a 7200 watt inverter. This inverter boasts a dual 4kW MPPT.  The OG-7.2 has a RGB light that changes colours depending on the inverter’s current working mode.

    More features of the OG-7.2:

    • 7200W of output power
    • Built in Wi-Fi for online monitoring via the IOS or Android app
    • BMS communication via RS485, makes it compatible with Pylontech,KODAK and Freedom Won batteries
    • Compatible with utilities main or generator
    • Built-in anti-dust kit
    • High Voltage MPPT, less PV cable means less cost and less installation time
    • Parallel up to 6 units

    View a complete range of KODAK systems and design a bespoke solution in seconds using Quick Quote.

    To ensure the inverter is properly protected, please see the AC Input Protection Application Note.

    View product
  • KODAK Solar Off-Grid Inverter VMIII 3kW 24V

    R10,523.31

    KODAK Off-grid inverter

    The OG 3.24 is ideal as an affordable and fully functional centre of your off-grid system.

    Wide MPP voltage range makes DC string design with your choice of module easy.

    Best suited to smaller domestic systems where no parallel operation is needed.

    Operates at 24V, so an ideal match with the Pylon US2500 24V model.

    • Removable LCD control module with multiple communications servers and ATM
    • Built-in Bluetooth for mobile monitoring (Android App is available)
    • Replaceable fan design for ease of maintenance
    • Supply load from Grid or PV, even battery is not available
    • Configurable AC/PV output usage timer and prioritization
    • Selectable high power charging current
    • Selectable input voltage range for home appliances and personal computers
    • Compatible to Utility Mains or generator input
    • Auto restart while AC is recovering
    • Cold start function
    Note: The Kodak VMIII inverter has a CAN-bus port included, which means a direct connection to Plyontech batteries is possible. Therefore no other control module, such as the ICC, is needed.
    View product
  • KODAK Solar Off-Grid Inverter VMIII 5kW 48V

    R12,420.00

    KODAK Off-grid inverter

    The OG 5.48 is ideal as an affordable and fully functional centre of your off-grid system.

    Wide MPP voltage range makes DC string design with your choice of module easy.

    Best suited to smaller domestic systems where no parallel operation is needed.

    • Removable LCD control module with multiple communications servers and ATM
    • Built-in Bluetooth for mobile monitoring (Android App is available)
    • Replaceable fan design for ease of maintenance
    • Supply load from Grid or PV, even battery is not available
    • Configurable AC/PV output usage timer and prioritization
    • Selectable high power charging current
    • Selectable input voltage range for home appliances and personal computers
    • Compatible to Utility Mains or generator input
    • Auto restart while AC is recovering
    • Cold start function
    Note: The Kodak King inverter has a RS485-bus port included, which means a direct connection to Plyontech batteries is possible. Therefore no other control module, such as the ICC, is needed.
    View product
  • KODAK Solar Off-Grid-X Inverter MKSII 5kW 48V

    KODAK Off-grid inverter

    The OGX 5.48 is ideal for domestic projects, and can be scaled up to deliver high loads across up to 9 parallet units.

    The high maximum DC input voltage makes DC string design simple and matches perfectly with Kodak’s high performance Percium modules.

    Consider adding the ICC Module for top-end remote monitoring of the installation and greater control over Pylontech batteries. Maximise your system.

    • Pure sine wave inverter
    • Output power factor 1
    • Built in high voltage range MPPT solar charge controller
    • Selectable input voltage range for home appliances and personal computers
    • Selectable charging current based on application
    • Configurable AC/Solar input priority via LCD setting
    • Compatible to mains voltage or generator power
    • Auto restart while AC is recovering
    • Overload and short circuit protection
    • Battery equalization for optimized battery performance and lifecyle
    • Cold start function
    • Built in parallel kit enabling parallel operation with up to 9 units
    View product
  • MECER 1200VA 1000W 12V W/MPPT INVERTER.

    R2,332.20

    Mecer IVR-1200MPPT 1200VA 1000W 12V DC-AC Inverter with LCD Display & MPPT built in, Cables are included to connect to the battery, 1x cable to connect to a South African 3pin wall socket is included, Requires 1x 12V deep cycle battery, Please note of connection: Connect RED cable to (+) on battery and BLACK cable to (-) on battery.

    Features

    • Simulated sinewave inverter

    • Wide input voltage range

    • 12VDC or 24VDC available

    • Overload and short circuit protection

    • LCD display for comprehensive information

    • Optional solar charger

     

     

    View product
  • Mecer 1Kw 12V 1x100A Battery Pure Sine Wave Inverter + 360W Solar Charge Controller (SOL-I-BB-M1)

    R7,820.00

    Mecer 1Kw 12V 1x100A Battery Pure Sine Wave Inverter + 360W Solar Charge Controller (SOL-I-BB-M1)

    The product applies to diversified loads because its digital design, pure sine wave output and excellent overcurrent protection can withstand the loads with a large starting current; the product is provided with independent solar three-stage charge management to improve charge efficiency of its battery and realize a longer life; the product provides universal 5VDC USB output port and 12VDC output to be widely applied to small solar power generation occasions including families, schools, street monitoring, forest monitoring, industrial and mining enterprises, frontier defense, sea islands, pasturing areas, etc.

    Main Features:

    • Excellent performance because of an MCU intelligent control technology
    • A wide range of applicable loads because of pure sine wave AC output
    • Convenient and practical 5VDC USB output port and 12VDC output port
    • Solar array and battery conrod-anode system input
    • Charge by mains supply for flexible configuration (optional function)
    • Overcharge protection and over discharge protection for a longer battery life
    • LCD and LEDS for visualization of operation status of the equipment
    • Overall automatic protection and alarms Including AC output over load protection, short circuit protection ,etc.
    View product
  • Mecer 2400VA, 1800W 24V W/MPPT Inverter

    R3,519.00

    Description

    • Inverter with MPPT
    • Simulated Sinewave Inverter
    • Wide Input Voltage Range
    • 12VDC or 24 24VDC available
    • Overload and shirt circuit protection
    • LCD display for comprehensive information
    • 55A MPPT
    View product
  • Mecer 2Kw 24V 2x100A Battery Pure Sine Wave Inverter + 720W Solar Charge Controller (SOL-I-BB-M2)

    R16,080.45

    Mecer 2Kw 24V 2x100A Battery Pure Sine Wave Inverter + 720W Solar Charge Controller (SOL-I-BB-M2)

    This inverter is ideal for diversified loads. It has a pure sine wave output with excellent overcurrent protection which can withstand loads with large starting currents. The inverter includes an independent solar three-stage charge management to improve the charge efficiency of the battery thereby extending the life of the battery. The inverter also has a universal 5VDC USB output port and 2VDC output.

    Main Features:

    • MCU intelligent control technology for best performance
    • Pure sine wave AC output to support a wide range of loads
    • Convenient 5VDC USB output port and 12VDC output port;
    • Solar array and battery common-anode system input;
    • Overcharge protection and over-discharge protection to preserve battery life;
    • LCD screen for visualization of operation status
    View product
  • Mecer 5kw 48V 80A MPPT Inverter

    R10,120.00

    MECER Axpert_MKS 5000VA / 5000W Hybrid Pure Sine Wave Inverter Power factor 1, MPPT Solar charge Controller 4000W 80Amp (solar panels not included), 220V AC Input, 48V DC Battery Input – requires deep cycle batteries (batteries not included), 80Amp AC Battery Charger, Overload and short circuit protection, Configurable AC/Solar Input Priority, 13.5Kg, Up to 9 of these unit can be connected in parallel. *Please take note of connection: Connect RED cable to (+) on battery and the (+) on the unit, and BLACK cable to (-) on battery and the (-) on the unit. Place cable lug directly onto the battery terminal first, follow up with the washer and then the lock washer, and then the nut. Do not put a washer between the battery terminal and cable. Connect the positive cable first. Follow instructions in manual.

    Overview:

    Axpert MKS Off-Grid Inverter
    Axpert MKS is equipped with MPPT solar charge controller to maximize and regulate DC power from the solar array for charging the battery bank. Transformerless design provides reliable power conversion in compact size. Besides, it’s worry-free to start up motor-type loads such as refrigerators, motors, pumps, compressors and laser printers as well as electronic loads like TVs, Computers, power tool and battery chargers.

    Features:

    • Pure sine wave inverter
    • Output power factor 1 (only 0.8 for 3KP/5KP Models)
    • Built-in battery equalization function to extend battery life cycle
    • Built-in MPPT solar charge controller
    • Selectable input voltage range for home appliances and personal computers
    • Selectable charging current based on applications
    • Configurable AC/Solar input priority via LCD setting
    • Compatible to mains voltage or generator power
    • Battery equalization for optimized battery performance and lifecycle
    • Parallel operation with up to 9 units only available for Axpert MKS 3KP/4KVA/5KVA*
    View product
  • Multiplus 12/1200/50-16

    R12,990.84

    Proven reliability
    The full bridge plus toroidal transformer topology has proven its reliability over many years.
    The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
    PowerControl – Dealing with limited generator, shore side or grid power
    With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
    is extra for charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
    compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
    High start-up power
    Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
    Search Mode
    When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
    operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
    exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
    Programmable relay
    By default, the programmable relay is set as
    an alarm relay, i.e. the relay will de-energise
    in the event of an alarm or a pre-alarm
    (inverter almost too hot, ripple on the input
    almost too high, battery voltage almost too
    low).
    Remote on / off / charger on
    Three pole connect

    View product
  • Multiplus 12/3000/120-50

    R28,725.83

    Multiplus, Multifunctional, with intelligent power management

    The Victron MultiPlus Inverter Charger is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next, to these primary functions, the MultiPlus has several advanced features, as outlined below.

    Two AC Outputs

    The main output has no-break functionality. The Victron MultiPlus Inverter Charger takes over the supply to the connected loads in the event of a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output (second output available on models rated at 3kVA and more).

    Virtually unlimited power thanks to parallel operation

    Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity.

    Three phase capability

    In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54 kVA three-phase inverter and 1260 A charger can be built.

    Split phase options

    Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30 kW / 36 kVA of split phase power. Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.

    PowerControl – Dealing with limited generator, shoreside or grid power

    The Victron MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

    PowerAssist – Boosting the capacity of shore or generator power

    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

    Four stage adaptive charger and dual bank battery charging

    The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the Victron MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.

    System configuring has never been easier

    After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

    View product
  • Multiplus 12/3000/120/16

    R26,603.97

    Multifunctional, with intelligent power management
    The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge
    technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the
    MultiPlus has several advanced features, as outlined below.
    Two AC Outputs
    The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of
    a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
    computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the
    battery, like a water heater for example, can be connected to this output (second output available on models rated at
    3kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide
    15kW / 18kVA output power with 420 Amps of charging capacity.
    Three phase capability
    In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three
    strings of six parallel units a 45 kW / 54 kVA three phase inverter and 1260 A charger can be built.
    Split phase options
    Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per
    phase, to supply up to 30 kW / 36 kVA of split phase power.
    Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on
    www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side
    supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore
    current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus
    preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the
    capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will
    make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When
    the load reduces, the spare power is used to recharge the battery.
    Four stage adaptive charger and dual bank battery charging
    The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software.
    The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage
    for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger
    datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second
    battery using an independent trickle charge output intended for a main engine or generator starter battery.
    System configuring has never been easier
    After installation, the MultiPlus is ready to go.
    If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even
    parallel and 3-phase operation can be programmed with DIP switches: no computer needed!
    Alternatively, VE.Net can be used instead of the DIP switches.
    And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several
    new, advanced, features

    View product
  • Multiplus 12/500/20-16

    R7,501.58

    Proven reliability
    The full bridge plus toroidal transformer topology has proven its reliability over many years.
    The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
    PowerControl – Dealing with limited generator, shore side or grid power
    With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
    is extra for charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
    compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
    High start-up power
    Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
    Search Mode
    When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
    operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
    exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
    Programmable relay
    By default, the programmable relay is set as
    an alarm relay, i.e. the relay will de-energise
    in the event of an alarm or a pre-alarm
    (inverter almost too hot, ripple on the input
    almost too high, battery voltage almost too
    low).
    Remote on / off / charger on
    Three pole connect

    View product
  • Multiplus 12/800/35-16

    R9,313.24

    Proven reliability
    The full bridge plus toroidal transformer topology has proven its reliability over many years.
    The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
    PowerControl – Dealing with limited generator, shore side or grid power
    With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
    is extra for charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
    compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
    High start-up power
    Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
    Search Mode
    When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
    operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
    exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
    Programmable relay
    By default, the programmable relay is set as
    an alarm relay, i.e. the relay will de-energise
    in the event of an alarm or a pre-alarm
    (inverter almost too hot, ripple on the input
    almost too high, battery voltage almost too
    low).
    Remote on / off / charger on
    Three pole connect

    View product
  • Multiplus 24/1200/25-16

    R12,990.84

    PowerControl / PowerAssist Yes
    Three Phase and parallel operation Yes
    Transfer switch 16A
    INVERTER
    Input voltage range 9,5 – 17V 19 – 33V 38– 66V
    Output Output voltage: 230VAC ± 2% Frequency: 50Hz ± 0,1% (1)
    Cont. output power at 25°C (3) 1200VA
    Cont. output power at 25°C 1000W
    Cont. output power at 40°C 900W
    Cont. output power at 65°C 600W
    Peak power 2400W
    Maximum efficiency 93 / 94 / 95%
    Zero-load power 10 / 9 / 10W
    Zero-load power in search mode 3/ 3 / 3W
    CHARGER
    AC Input Input voltage range: 187-265 VAC Input frequency: 45 – 65 Hz
    Charge voltage ‘absorption’ 14,4 / 28,8 / 57,6V
    Charge voltage ‘float’ 13,8 / 27,6 / 55,2V
    Storage mode 13,2 / 26,4 /52,8V
    Charge current house battery (4) 50 / 25 / 13A
    Charge current starter battery 1A (12V and 24V models only)
    Battery temperature sensor Yes
    GENERAL
    Programmable relay (5) Yes
    Protection (2) a – g
    VE.Bus communication port For parallel and three phase operation, remote monitoring and system integration
    (RJ45-spliter ASS030065510 needed for 500/800/12ooVA models)
    Remote on-off On/off/charger only On/off
    DIP switches Yes (6) Yes (3)
    Internal DC fuse 200/100/50A
    Common Characteristics Operating temp. range: -40 to +65°C (fan assisted cooling)
    Humidity (non-condensing): max 95%
    ENCLOSURE
    Common Characteristics Material & Colour: Steel/ABS (blue RAL 5012) Protection category: IP 21
    Battery-connection 35 / 25 / 10 mm²
    230V AC-connection G-ST18i connector
    Weight 8,2 kg
    Dimensions (h x w x d) 406 x 250 x 100 mm
    STANDARDS
    Safety EN-IEC 60335-1, EN-IEC 60335-2-29, EN 62109-1
    Emission / Immunity EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3
    IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
    Road vehicles ECE R10-5
    1) Can be adjusted to 60Hz and to 240V
    2) Protection
    a. Output short circuit
    b. Overload
    c. Battery voltage too high
    d. Battery voltage too low
    e. Temperature too high
    f. 230VAC on inverter output
    g. Input voltage ripple too high
    3) Non-linear load, crest factor 3:1
    4) At 25°C ambient
    5) Programmable relay which can be set for:
    general alarm, DC under voltage or generator start/stop signal function
    AC rating: 230V/4A
    DC rating: 4A up to 35VDC, 1A up to 60VDC

    View product
  • Multiplus 24/3000/70-16

    R26,603.97

    Multiplus, Multifunctional, with intelligent power management

    The Victron MultiPlus Inverter Charger is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next, to these primary functions, the MultiPlus has several advanced features, as outlined below.

    Two AC Outputs

    The main output has no-break functionality. The Victron MultiPlus Inverter Charger takes over the supply to the connected loads in the event of a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output (second output available on models rated at 3kVA and more).

    Virtually unlimited power thanks to parallel operation

    Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity.

    Three phase capability

    In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54 kVA three-phase inverter and 1260 A charger can be built.

    Split phase options

    Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30 kW / 36 kVA of split phase power. Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.

    PowerControl – Dealing with limited generator, shoreside or grid power

    The Victron MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

    PowerAssist – Boosting the capacity of shore or generator power

    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

    Four stage adaptive charger and dual bank battery charging

    The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the Victron MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.

    System configuring has never been easier

    After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

    View product
  • Multiplus 24/3000/70-50

    R28,725.83

    Multiplus, Multifunctional, with intelligent power management

    The Victron MultiPlus Inverter Charger is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next, to these primary functions, the MultiPlus has several advanced features, as outlined below.

    Two AC Outputs

    The main output has no-break functionality. The Victron MultiPlus Inverter Charger takes over the supply to the connected loads in the event of a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output (second output available on models rated at 3kVA and more).

    Virtually unlimited power thanks to parallel operation

    Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity.

    Three phase capability

    In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54 kVA three-phase inverter and 1260 A charger can be built.

    Split phase options

    Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30 kW / 36 kVA of split phase power. Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.

    PowerControl – Dealing with limited generator, shoreside or grid power

    The Victron MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

    PowerAssist – Boosting the capacity of shore or generator power

    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

    Four stage adaptive charger and dual bank battery charging

    The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three-stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the Victron MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.

    System configuring has never been easier

    After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

    View product
  • Multiplus 24/500/10-16

    R7,501.58

    Proven reliability
    The full bridge plus toroidal transformer topology has proven its reliability over many years.
    The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
    PowerControl – Dealing with limited generator, shore side or grid power
    With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
    is extra for charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
    compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
    High start-up power
    Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
    Search Mode
    When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
    operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
    exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
    Programmable relay
    By default, the programmable relay is set as
    an alarm relay, i.e. the relay will de-energise
    in the event of an alarm or a pre-alarm
    (inverter almost too hot, ripple on the input
    almost too high, battery voltage almost too
    low).
    Remote on / off / charger on
    Three pole connect

    View product
  • Multiplus 24/5000/120-100

    R42,558.99

    Multifunctional, with intelligent power management
    The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge
    technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the
    MultiPlus has several advanced features, as outlined below.
    Two AC Outputs
    The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of
    a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
    computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the
    battery, like a water heater for example, can be connected to this output (second output available on models rated at
    3kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide
    15kW / 18kVA output power with 420 Amps of charging capacity.
    Three phase capability
    In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three
    strings of six parallel units a 45 kW / 54 kVA three phase inverter and 1260 A charger can be built.
    Split phase options
    Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per
    phase, to supply up to 30 kW / 36 kVA of split phase power.
    Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on
    www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side
    supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore
    current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus
    preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the
    capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will
    make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When
    the load reduces, the spare power is used to recharge the battery.
    Four stage adaptive charger and dual bank battery charging
    The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software.
    The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage
    for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger
    datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second
    battery using an independent trickle charge output intended for a main engine or generator starter battery.
    System configuring has never been easier
    After installation, the MultiPlus is ready to go.
    If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even
    parallel and 3-phase operation can be programmed with DIP switches: no computer needed!
    Alternatively, VE.Net can be used instead of the DIP switches.
    And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several
    new, advanced, features

    View product
  • Multiplus 24/800/16-16

    R9,014.24

    Proven reliability
    The full bridge plus toroidal transformer topology has proven its reliability over many years.
    The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
    PowerControl – Dealing with limited generator, shore side or grid power
    With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
    is extra for charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
    compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
    High start-up power
    Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
    Search Mode
    When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
    operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
    exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
    Programmable relay
    By default, the programmable relay is set as
    an alarm relay, i.e. the relay will de-energise
    in the event of an alarm or a pre-alarm
    (inverter almost too hot, ripple on the input
    almost too high, battery voltage almost too
    low).
    Remote on / off / charger on
    Three pole connect

    View product
  • Multiplus 48/3000/35-16

    R21,553.82

    Multifunctional, with intelligent power management
    The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge
    technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the
    MultiPlus has several advanced features, as outlined below.
    Two AC Outputs
    The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of
    a grid failure or when shore-/generator power is disconnected. This happens so fast (less than 20 milliseconds) that
    computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the
    battery, like a water heater for example, can be connected to this output (second output available on models rated at
    3kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units, for example, provide
    15kW / 18kVA output power with 420 Amps of charging capacity.
    Three phase capability
    In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three
    strings of six parallel units a 45 kW / 54 kVA three phase inverter and 1260 A charger can be built.
    Split phase options
    Two units can be stacked to provide 120-0-120 V, and additional units can be paralleled up to a total of 6 units per
    phase, to supply up to 30 kW / 36 kVA of split phase power.
    Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on
    www.victronenergy.com) to a ‘European’ inverter programmed to supply 240 V / 60 Hz.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side
    supply (nearly 20 A per 3 kVA MultiPlus at 120 VAC). With the Multi Control Panel a maximum generator or shore
    current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus
    preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the
    capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will
    make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When
    the load reduces, the spare power is used to recharge the battery.
    Four stage adaptive charger and dual bank battery charging
    The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software.
    The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage
    for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger
    datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second
    battery using an independent trickle charge output intended for a main engine or generator starter battery.
    System configuring has never been easier
    After installation, the MultiPlus is ready to go.
    If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even
    parallel and 3-phase operation can be programmed with DIP switches: no computer needed!
    Alternatively, VE.Net can be used instead of the DIP switches.
    And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several
    new, advanced, features

    View product
  • Multiplus 48/500/6-16

    R7,195.27

    Proven reliability
    The full bridge plus toroidal transformer topology has proven its reliability over many years.
    The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
    PowerControl – Dealing with limited generator, shore side or grid power
    With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever
    is extra for charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately
    compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
    High start-up power
    Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
    Search Mode
    When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when
    operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current
    exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
    Programmable relay
    By default, the programmable relay is set as
    an alarm relay, i.e. the relay will de-energise
    in the event of an alarm or a pre-alarm
    (inverter almost too hot, ripple on the input
    almost too high, battery voltage almost too
    low).
    Remote on / off / charger on
    Three pole connect

    View product
  • Multiplus 48/800/9-16

    R9,807.59

    PowerControl / PowerAssist Yes
    Three Phase and parallel operation Yes
    Transfer switch 16A
    INVERTER
    Input voltage range 9,5 – 17V 19 – 33V 38– 66V
    Output Output voltage: 230VAC ± 2% Frequency: 50Hz ± 0,1% (1)
    Cont. output power at 25°C (3) 800VA
    Cont. output power at 25°C 700W
    Cont. output power at 40°C 650W
    Cont. output power at 65°C 400W
    Peak power 1600W
    Maximum efficiency 92 / 93 / 94%
    Zero-load power 7 / 7 / 8W
    Zero-load power in search mode 2 / 2 / 3W
    CHARGER
    AC Input Input voltage range: 187-265 VAC Input frequency: 45 – 65 Hz
    Charge voltage ‘absorption’ 14,4 / 28,8 / 57,6V
    Charge voltage ‘float’ 13,8 / 27,6 / 55,2V
    Storage mode 13,2 / 26,4 /52,8V
    Charge current house battery (4) 35 / 16 / 9A
    Charge current starter battery 1A (12V and 24V models only)
    Battery temperature sensor Yes
    GENERAL
    Programmable relay (5) Yes
    Protection (2) a – g
    VE.Bus communication port For parallel and three phase operation, remote monitoring and system integration
    (RJ45-spliter ASS030065510 needed for 500/800/12ooVA models)
    Remote on-off On/off/charger only On/off
    DIP switches Yes (6) Yes (3)
    Internal DC fuse 150/80/40A
    Common Characteristics Operating temp. range: -40 to +65°C (fan assisted cooling)
    Humidity (non-condensing): max 95%
    ENCLOSURE
    Common Characteristics Material & Colour: Steel/ABS (blue RAL 5012) Protection category: IP 21
    Battery-connection 25 / 16 / 10 mm²
    230V AC-connection G-ST18i connector
    Weight 6,4 kg
    Dimensions (h x w x d) 360 x 240 x 100 mm
    STANDARDS
    Safety EN-IEC 60335-1, EN-IEC 60335-2-29, EN 62109-1
    Emission / Immunity EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3
    IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
    Road vehicles ECE R10-5
    1) Can be adjusted to 60Hz and to 240V
    2) Protection
    a. Output short circuit
    b. Overload
    c. Battery voltage too high
    d. Battery voltage too low
    e. Temperature too high
    f. 230VAC on inverter output
    g. Input voltage ripple too high
    3) Non-linear load, crest factor 3:1
    4) At 25°C ambient
    5) Programmable relay which can be set for:
    general alarm, DC under voltage or generator start/stop signal function
    AC rating: 230V/4A
    DC rating: 4A up to 35VDC, 1A up to 60VDC

    View product
  • Multiplus COMPACT 12/1200/50-16

    R16,851.97

    Two AC Outputs
    The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the
    event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than
    20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not
    discharge the battery, like a water heater for example can be connected to this output (second output available
    on models rated at 3 kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will
    provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
    Three phase capability
    In addition to parallel connection, three units of the same model can be configured for three phase output. But
    that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more
    than 2000 Amps charging capacity.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or
    shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator
    or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for
    charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement
    the capacity of the alternative source. Where peak power is so often required only for a limited period, the
    MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power
    from the battery. When the load reduces, the spare power is used to recharge the battery.
    Solar energy: AC power available even during a grid failure
    The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems.
    Loss of mains detection software is available.
    System configuring
    – In case of a stand-alone application, if settings have to be changed, this can be done in a matter of
    minutes with a DIP switch setting procedure.
    – Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
    – Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT
    Solar Chargers can be configured with Assistants (dedicated software for specific applications).
    On-site Monitoring and control
    Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices,
    smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
    Remote Monitoring and control
    Color Control GX or other GX devices.
    Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
    Remote configuring
    When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and
    settings can be changed remotely.

    View product
  • Multiplus COMPACT 12/1600/70-16

    R17,235.49

    Two AC Outputs
    The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the
    event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than
    20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not
    discharge the battery, like a water heater for example can be connected to this output (second output available
    on models rated at 3 kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will
    provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
    Three phase capability
    In addition to parallel connection, three units of the same model can be configured for three phase output. But
    that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more
    than 2000 Amps charging capacity.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or
    shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator
    or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for
    charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement
    the capacity of the alternative source. Where peak power is so often required only for a limited period, the
    MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power
    from the battery. When the load reduces, the spare power is used to recharge the battery.
    Solar energy: AC power available even during a grid failure
    The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems.
    Loss of mains detection software is available.
    System configuring
    – In case of a stand-alone application, if settings have to be changed, this can be done in a matter of
    minutes with a DIP switch setting procedure.
    – Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
    – Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT
    Solar Chargers can be configured with Assistants (dedicated software for specific applications).
    On-site Monitoring and control
    Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices,
    smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
    Remote Monitoring and control
    Color Control GX or other GX devices.
    Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
    Remote configuring
    When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and
    settings can be changed remotely.

    View product
  • Multiplus COMPACT 12/2000/80-30

    R21,535.38

    Two AC Outputs
    The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the
    event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than
    20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not
    discharge the battery, like a water heater for example can be connected to this output (second output available
    on models rated at 3 kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will
    provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
    Three phase capability
    In addition to parallel connection, three units of the same model can be configured for three phase output. But
    that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more
    than 2000 Amps charging capacity.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or
    shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator
    or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for
    charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement
    the capacity of the alternative source. Where peak power is so often required only for a limited period, the
    MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power
    from the battery. When the load reduces, the spare power is used to recharge the battery.
    Solar energy: AC power available even during a grid failure
    The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems.
    Loss of mains detection software is available.
    System configuring
    – In case of a stand-alone application, if settings have to be changed, this can be done in a matter of
    minutes with a DIP switch setting procedure.
    – Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
    – Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT
    Solar Chargers can be configured with Assistants (dedicated software for specific applications).
    On-site Monitoring and control
    Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices,
    smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
    Remote Monitoring and control
    Color Control GX or other GX devices.
    Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
    Remote configuring
    When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and
    settings can be changed remotely.

    View product
  • Multiplus COMPACT 12/800/35-16

    R13,466.76

    Two AC Outputs
    The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the
    event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than
    20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not
    discharge the battery, like a water heater for example can be connected to this output (second output available
    on models rated at 3 kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will
    provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
    Three phase capability
    In addition to parallel connection, three units of the same model can be configured for three phase output. But
    that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more
    than 2000 Amps charging capacity.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or
    shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator
    or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for
    charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement
    the capacity of the alternative source. Where peak power is so often required only for a limited period, the
    MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power
    from the battery. When the load reduces, the spare power is used to recharge the battery.
    Solar energy: AC power available even during a grid failure
    The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems.
    Loss of mains detection software is available.
    System configuring
    – In case of a stand-alone application, if settings have to be changed, this can be done in a matter of
    minutes with a DIP switch setting procedure.
    – Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
    – Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT
    Solar Chargers can be configured with Assistants (dedicated software for specific applications).
    On-site Monitoring and control
    Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices,
    smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
    Remote Monitoring and control
    Color Control GX or other GX devices.
    Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
    Remote configuring
    When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and
    settings can be changed remotely.

    View product
  • Multiplus COMPACT 24/1200/25-16

    R16,851.63

    Two AC Outputs
    The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the
    event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than
    20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not
    discharge the battery, like a water heater for example can be connected to this output (second output available
    on models rated at 3 kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will
    provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
    Three phase capability
    In addition to parallel connection, three units of the same model can be configured for three phase output. But
    that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more
    than 2000 Amps charging capacity.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or
    shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator
    or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for
    charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement
    the capacity of the alternative source. Where peak power is so often required only for a limited period, the
    MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power
    from the battery. When the load reduces, the spare power is used to recharge the battery.
    Solar energy: AC power available even during a grid failure
    The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems.
    Loss of mains detection software is available.
    System configuring
    – In case of a stand-alone application, if settings have to be changed, this can be done in a matter of
    minutes with a DIP switch setting procedure.
    – Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
    – Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT
    Solar Chargers can be configured with Assistants (dedicated software for specific applications).
    On-site Monitoring and control
    Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices,
    smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
    Remote Monitoring and control
    Color Control GX or other GX devices.
    Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
    Remote configuring
    When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and
    settings can be changed remotely.

    View product
  • Multiplus COMPACT 24/1600/40-16

    R17,235.49

    Two AC Outputs
    The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the
    event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than
    20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not
    discharge the battery, like a water heater for example can be connected to this output (second output available
    on models rated at 3 kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will
    provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
    Three phase capability
    In addition to parallel connection, three units of the same model can be configured for three phase output. But
    that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more
    than 2000 Amps charging capacity.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or
    shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator
    or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for
    charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement
    the capacity of the alternative source. Where peak power is so often required only for a limited period, the
    MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power
    from the battery. When the load reduces, the spare power is used to recharge the battery.
    Solar energy: AC power available even during a grid failure
    The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems.
    Loss of mains detection software is available.
    System configuring
    – In case of a stand-alone application, if settings have to be changed, this can be done in a matter of
    minutes with a DIP switch setting procedure.
    – Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
    – Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT
    Solar Chargers can be configured with Assistants (dedicated software for specific applications).
    On-site Monitoring and control
    Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices,
    smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
    Remote Monitoring and control
    Color Control GX or other GX devices.
    Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
    Remote configuring
    When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and
    settings can be changed remotely.

    View product
  • Multiplus COMPACT 24/2000/50-30

    R21,535.38

    Two AC Outputs
    The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the
    event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than
    20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
    The second output is live only when AC is available on the input of the MultiPlus. Loads that should not
    discharge the battery, like a water heater for example can be connected to this output (second output available
    on models rated at 3 kVA and more).
    Virtually unlimited power thanks to parallel operation
    Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will
    provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
    Three phase capability
    In addition to parallel connection, three units of the same model can be configured for three phase output. But
    that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more
    than 2000 Amps charging capacity.
    PowerControl – Dealing with limited generator, shore side or grid power
    The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or
    shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator
    or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for
    charging, thus preventing the generator or shore supply from being overloaded.
    PowerAssist – Boosting the capacity of shore or generator power
    This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement
    the capacity of the alternative source. Where peak power is so often required only for a limited period, the
    MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power
    from the battery. When the load reduces, the spare power is used to recharge the battery.
    Solar energy: AC power available even during a grid failure
    The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems.
    Loss of mains detection software is available.
    System configuring
    – In case of a stand-alone application, if settings have to be changed, this can be done in a matter of
    minutes with a DIP switch setting procedure.
    – Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
    – Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT
    Solar Chargers can be configured with Assistants (dedicated software for specific applications).
    On-site Monitoring and control
    Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices,
    smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
    Remote Monitoring and control
    Color Control GX or other GX devices.
    Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
    Remote configuring
    When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and
    settings can be changed remotely.

    View product

Filter by price

Go to Top